GasGas Riders Club Forum  

Go Back   GasGas Riders Club Forum > GasGas Enduro Technical Forums > Enduro Electrical & Wiring

Enduro Electrical & Wiring Lighting, Ignition, Wiring, Plugs, etc.


Reply
 
Thread Tools Display Modes
  #1  
Old 12-24-2018, 03:46 AM
Doc Brown Doc Brown is offline
Senior Member
 
Join Date: Dec 2017
Location: Austria, Europe
Posts: 586
Default will 2019 map switch fit 2018

My dealer says the 2019 map switch, which is an ignition curve switch, will fit the 2018 models aswell.

But I didnt find a connector on my friends GP300/18. So I wonder if there is a connector on the EC300/18 and if not how can I fit the switch?


Reply With Quote


  #2  
Old 12-24-2018, 04:50 AM
RudolfHucker's Avatar
RudolfHucker RudolfHucker is offline
Senior Member
 
Join Date: Oct 2018
Location: Central UK
Posts: 170
Default

The 2018 and 2019 wiring diagrams are identical.

The map switch connects to pin #4 on the CDI unit and the switch simply connects the pin to ground for the "wet" curve. If the switch is not connected, the CDI is set to "sun" curve.

I usually run my bikes on the "wet" curve by removing the switch and connecting a wire across the connector under the tank to short pin #4. Personal preference.

On the 2019, the connector is is a simple 2 pin type under the tank near the HT coil. you should be able to trace it from the CDI connector.
Reply With Quote
  #3  
Old 12-24-2018, 07:04 AM
gasgasman's Avatar
gasgasman gasgasman is offline
Super Moderator
 
Join Date: Jul 2006
Location: Pearland Texas
Posts: 4,491
Default

CDI connectors can be found on eBay.
You can use the wire terminals from one of those.

I'm not sure if the '18 CDI module supports the map modes.
Reply With Quote
  #4  
Old 12-24-2018, 05:54 PM
AZRickD AZRickD is offline
Senior Member
 
Join Date: Feb 2007
Posts: 1,839
Default

What are the part numbers for the 2018 and 2019 CDIs ??
Reply With Quote
  #5  
Old 12-25-2018, 04:02 AM
Doc Brown Doc Brown is offline
Senior Member
 
Join Date: Dec 2017
Location: Austria, Europe
Posts: 586
Default

Quote:
Originally Posted by RudolfHucker View Post
The 2018 and 2019 wiring diagrams are identical.

The map switch connects to pin #4 on the CDI unit and the switch simply connects the pin to ground for the "wet" curve. If the switch is not connected, the CDI is set to "sun" curve.

I usually run my bikes on the "wet" curve by removing the switch and connecting a wire across the connector under the tank to short pin #4. Personal preference.

On the 2019, the connector is is a simple 2 pin type under the tank near the HT coil. you should be able to trace it from the CDI connector.
Many thanks, so you're saying there should be a connector under the tank on the 2018? Well, if not we can ground the #4 pin on the CDI to activate the softer curve.

On the 2019 it was as you said, I just had to plug in the switch which came with the bike.
Reply With Quote
  #6  
Old 12-25-2018, 05:53 PM
GASGASCWB GASGASCWB is offline
Senior Member
 
Join Date: Sep 2018
Posts: 101
Default

Quote:
Originally Posted by AZRickD View Post
What are the part numbers for the 2018 and 2019 CDIs ??
EC300 2018: CDI PN: EE51100CT-CRB-1
XC300 2018: CDI PN: EE51100CT-CRB-1
GP300 2018: CDI PN: EE51100CT-CRB-1

EC300 2019: CDI PN: EE51100CT-CLP-2
XC300 2019: CDI PN: EE51100CT-CLP-2
GP300 2019: CDI PN: EE51100CT-CSK-2

I think the PNs have changed because of reprogramming...
Reply With Quote
  #7  
Old 12-26-2018, 09:42 AM
Undertow Undertow is offline
Member
 
Join Date: Oct 2018
Posts: 32
Default

This was good news. Don?t have any map switches on my 125 (have throttle for that), but it?s good to know that ecu on my 2018 GP300 has the possibility to fit the map switch. Actually looking at the 2019 manual one can scheck the correct pins and correct color codes for wires.
Reply With Quote
  #8  
Old 12-26-2018, 12:33 PM
gasgasman's Avatar
gasgasman gasgasman is offline
Super Moderator
 
Join Date: Jul 2006
Location: Pearland Texas
Posts: 4,491
Default

The CDI connector terminals (for MAP switch) are blank on the "18s.
Pins 4 and 13 are for the MAP switch.
Reply With Quote
  #9  
Old 12-26-2018, 01:58 PM
GASGASCWB GASGASCWB is offline
Senior Member
 
Join Date: Sep 2018
Posts: 101
Default

Quote:
Originally Posted by gasgasman View Post
The CDI connector terminals (for MAP switch) are blank on the "18s.
Pins 4 and 13 are for the MAP switch.

Finally,
If I buy the selector switch and install it in aEC 300 2018 as you described, will I have the RAIN and SUN maps on my bike, like 2019 models?
Reply With Quote
  #10  
Old 12-26-2018, 04:39 PM
gasgasman's Avatar
gasgasman gasgasman is offline
Super Moderator
 
Join Date: Jul 2006
Location: Pearland Texas
Posts: 4,491
Default

No.
According to the GG tech, if the '18 CDI supported the MAP switch, they would have added it.
You can buy a '19 CDI and add the switch.
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Converting 2018 EC/GP to XC start switch Keg Enduro Electrical & Wiring 6 02-28-2021 04:25 PM
Swingarm Decals GG300 2018/2019 Doc Brown Enduro Chassis & Body 9 10-14-2019 10:18 AM
Aftermarket Plastics for 2018/2019 EC Models RudolfHucker Enduro Chassis & Body 0 11-08-2018 07:12 AM
Adding a map switch to 2018 XC/EC AZRickD Enduro Electrical & Wiring 9 08-29-2018 12:25 PM
Start/Light switch and kill switch Doc Brown Enduro Electrical & Wiring 0 07-27-2018 12:43 PM




All times are GMT -5. The time now is 09:37 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2022, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org