|
Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Full Tools to Have for a GASGAS EC
Hi,
I am building up my tools set which should be able to cover repair for the entire ec bike ...... piston, clutch replacement etc What do I nned to have? |
#2
|
|||
|
|||
All of 'em. lol.
GG uses about every different form of fastener in existence. |
#3
|
||||
|
||||
Yup, the learning curve has already pissed me off but I was in a bit of a hurry at the time and the swears were ah flying.
__________________
07 EC 300 (under 500 miles, selling soon) 97 KTM 250 EXC (sold) 2016 Trek Remedy 29er |
#4
|
||||
|
||||
The newer '07+ bikes have more consistent sizes, but still a bunch. You could always buy a KTM bolt replacement kit and swap some out. However, then our GG's will get orange koolaid intoxication.
__________________
Matt Current: 2009 Yamaha FZ1 Previous: 2001 GasGas TXT280, 2001 GasGas XC250, 2004 KTM 200EXC, 2007 GasGas EC250, 2007 Husqvarna SM610, 2008 Husqvarna WB165 |
#5
|
||||
|
||||
Quote:
Something I could add - I had a couple spare boxes of KTM replacement fasteners from Motion Pro, and I replaced all the weirdo, oddball stuff I could with more normal bits in an effort to minimize the toolkit I had to carry in the sticks when riding.
__________________
gaspipe [the original] -------------------- '04 Gasgas 300EC Bruce's Suspension F&R revalve-Zokes & .48 fork springs, Ohlins & 5.8 rear spring, Scotts damper, Hyde skidplate, Clarke tank, Knight powervalve cover, LTR jetting/waterpump impeller/exhaust spigot, Wiseco piston, ICW reinforced KTM RFS Fluidyne radiators, Hammerhead shift lever, GoFasters seat, Allen hardware conversion, UFO LED tail light, Dunlop 756, Michelin X11, and TN street plated....killer trail ride machine |
#6
|
||||
|
||||
That's what i'm doing, the fixings are a better quality also.
|
#7
|
|||
|
|||
I wanna bring this one back from the dead. Assume I know very little. Assume that I have very few tools. Start from there, and tell me what is in your must-have tool box for working on your GG 2 stroke.
|
#8
|
||||
|
||||
Man they are not joking on this one
Just to start the biggest set mm sockets you can find the biggest set mm wrench you can find the biggest set of mm allen wrenches you can find full set of torx (star) sockets you can find screw driver set hammer (if the bike is used) pry bar BIG jug of corn whiskey home made preferably but that may be hard to find in Perris
__________________
02 EC 200 03 MC 250 88 VT 800 01 TXT 280 |
#9
|
|||
|
|||
Sounds like a really good, if daunting start. Oh, well, I guess there's Harbor Freight, although the quality of tools there I don't think is what I'm looking for.
Quote:
|
#10
|
||||
|
||||
15mm yup never knew I owned one till I started wrench'n on a GG.
__________________
HuskyDude 10 EC300XC 08 TE510 07 TXT 280 77 TY175 |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Bux Tools C clipper | GMP | Enduro Product Reviews | 2 | 02-01-2010 10:07 AM |
Air box full of oil | dukbil | Enduro Engine 4 stroke (including EFI & Exhaust) | 10 | 04-02-2009 08:46 PM |
Full throttle? | Krasi | Riding Techniques & Training | 8 | 01-29-2009 01:15 AM |
LTR PV cover full of fluid? | socalscott | Enduro Engine - 2 stroke | 4 | 05-08-2008 01:06 PM |