|
Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
troubles with.....something?
My son got an 03 EC250 and it ran great at first (month ago). It started running rich and fouling plugs. I checked the jetting (seemed to be right in the middle what everyone else is running on the sticky, cleaned the holes, checked the enrichment (seemed to close off). It is very intermitent. It will run fine for a while then foul a plug and start loading up. Its getting worse, and now it will start great, nice and crisp for a few seconds, then load up when you give it gas. It will spit and spudder, and I even caught it making a sucking sound from the pipe and then shot out a puff of black smoke (but didn't die). I can ride it and it will start doing better and finally clean up and do fine. My son rode it Sunday about 25 miles. It did fine. I then started it up to load it and it did terrible like above. It acts like its going to die out, spit and sputter and suck. My next check will be the reeds, is the anything else I need to check while I am around there? Crank seals? Other ideas?
__________________
2006 EC300, 2000 XR650R, 2003 EC250, 2001 EC200 (OK, the last two are really my sons). |
#2
|
||||
|
||||
sounds like a busted reed to me.
|
#3
|
||||
|
||||
Another possibility is a leaky right crank seal letting gear oil to be sucked in and burned.
|
#4
|
|||
|
|||
Took the reeds out and they were not seating very well. I turned them over and they did much better. I have heard about folks doing this and never having any more problems. I imagine it was from where the bike sat for a long time. Also going to have to rebuild the clutch master as it seems to be leaking a bit (from sitting???).
__________________
2006 EC300, 2000 XR650R, 2003 EC250, 2001 EC200 (OK, the last two are really my sons). |
#5
|
|||
|
|||
Still troubles
After I flipped the reeds I still had some problems, so I switched them. Still troubles. Looks like seal is next....
__________________
2006 EC300, 2000 XR650R, 2003 EC250, 2001 EC200 (OK, the last two are really my sons). |
#6
|
||||
|
||||
i had the same trouble as you.. i replaced the seals on the crank and noticed that the powervalve was set wrong now it starts straight away and rips
|
#7
|
|||
|
|||
My problem
I think I have figured out my problem. My 14 year old son is riding the bike and he is new to a 2T. One of our favorite places to ride ends up back at the truck at the bottom of a long tight hill. He is tired when we finish up and just lets it coast for the last minute or two not really giving any throttle and maybe lugging it really bad in a high gear. This is loading the plug and screwing it up. When I try and start it up later it may or may not start and if it does its so fouled it wont run right all through the throttle making me think something else is up. I also took the air screw out to 2 turns and I may thin out the pilot to help (part of the problem is it may be a little rich at idle, but don't really think so. Its hard to tell because as you know all 2 strokes want to load after a few seconds at idle). Maybe this will help someone else down the road! Glad I didn't change the seals....
__________________
2006 EC300, 2000 XR650R, 2003 EC250, 2001 EC200 (OK, the last two are really my sons). |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Trail tech troubles | skid jackson | General Discussions & Announcements | 8 | 06-02-2010 07:15 PM |
Dunlop 803 troubles keeping it on | kendunn | Enduro Chassis & Body | 15 | 04-22-2010 04:50 PM |
Tube troubles! Need help. | svt2224 | Enduro Chassis & Body | 19 | 10-12-2008 07:50 PM |
300ec 2001 Engine Troubles | toka2020 | General Discussions & Announcements | 1 | 06-05-2008 03:46 PM |