|
Enduro Chassis & Body Enduro Frame, Plastic, Brakes, Bars, Controls, wheels, tires, sprockets & gearing. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Gasgas wheel crossover think tank
Looking to see if we can find a rear and front hub similar to gasgas.
The most important factor is the distance from outer sprocket to outer rotor. I can figure out the spacer/collar/bearing arrangement later. Rear hub on the GasGas outer sprocket to outer rotor is: 6 3/8 Front hub measure from outer of rotor to outer hub flange: 4 5/8 The rear of a 99-18 YZ/YZF comes in at 6 3/8 Front 4 3/8 It looks like a rear wheel of a Yamaha can fit with the a different configuration of custom collars. Has any tried? If we can find a front hub that matches 4 5/8, that will give many options. |
#2
|
||||
|
||||
Just curious, did you happen to think about axle diameters?
As for the front YZ wheel, as long as you can get the rotor to line up with the caliper, and the axle fits (possibly could switch bearings to fit?), you can re-true the rim to be centered even if the hub isn't. Done it before on a wheel swap with no problems.
__________________
WildAzzRacing YouTube channel Trail Riders of Southern AZ club AZ State Parks OHV Ambassador '11 EC250R '98 KDX220 |
#3
|
|||
|
|||
I just talked to Warp 9 about this the other day. The front hub is an exact match to a red Husqvarna (pre-13). When they build a wheel for the rear, they use a CRF wheel. One thing I did t think to ask was, what year crf. I know the hub width changed in them in 2013.
Sent from my iPhone using Tapatalk |
#4
|
|||
|
|||
Quote:
|
#5
|
||||
|
||||
Quote:
|
#6
|
|||
|
|||
Quote:
I bought some to mount my studded tires on so I'm not swapping every week through the winter and when they showed up I tried mounting them and they don't fit. Warp9 has been amiable working over the phone trying to get spacer size dialed in but I'm afraid it's going to be a process. I don't know if they've sold a set for the new bikes other than mine. On my first set of spacers for The rear the wheel sits too close to the swing arm on the sprocket side and the chain rubs heavily on the chain slider on the swing arm. On the rotor side the spacer size makes the rotor have constant contact with the non floating brake pad. On the front it's believed I got one incorrect spacer because it has the wrong external diameter to fit inside of the grease seal. The other front spacer fits inside the grease seal but has twice as much play on the axle as OEM spacers. 0.003' measured difference on internal diameter which seams significant when the torque value for these wheels are 50% lighter than the manual states for OEM axle torque. If anyone else has these wheels I'm interested in your findings. |
#7
|
|||
|
|||
I have a set of these PM sent
|
#8
|
|||
|
|||
Quote:
__________________
2003 txt250 Pro 2013 Ossa 280i |
#9
|
||||
|
||||
Only downsides are if your trying to move it too much and that it is a tedious process. If you have sufficient spoke length you should be fine. Just take your time and loosen first then tighten the opposite spoke. I like to do 1/4 turn loosen/tighten at a time. If you do it this way you'll keep your wheel true.
__________________
WildAzzRacing YouTube channel Trail Riders of Southern AZ club AZ State Parks OHV Ambassador '11 EC250R '98 KDX220 |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
2009 Husky 300 rear wheel crossover? | sam | Enduro Chassis & Body | 0 | 01-15-2015 06:34 PM |
Wheel crossover ? | Cberg | Enduro Chassis & Body | 2 | 10-09-2012 10:02 AM |
GG-Jap Bike Front Wheel Bearing Crossover | unclejosh | General Discussions & Announcements | 1 | 05-15-2011 02:53 PM |
2003 EC 300 Gas tank cap crossover | GasGasser | Enduro Chassis & Body | 0 | 04-02-2010 05:10 AM |
Wheel crossover for 2004 Gas gas MC 250 | FFRDave | Enduro Chassis & Body | 5 | 01-04-2008 07:28 AM |