|
General Discussions & Announcements General Announcements, General Questions, e.g. What bike do I buy?, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
fork bleeder screws and orings
Where can I get some extra bleeder screws and 0-rings for my front forks? This is the third time this year I've lost one. Lucky for me I can take one off my ec250 for tomorrow's ride.
What is the size/description? maybe a hardware store might have them and the o'rings? They fit my '05 de300 with the 45 Zokes. Thanks in advance.
__________________
'14 Beta 300rr '05 GG DE300 '03 GG EC250 '01 XR440 '09 FZ1 |
#2
|
||||
|
||||
Why not buy some push button bleeders?
Last edited by gasgasman; 09-07-2012 at 10:23 PM. Reason: spelling |
#3
|
|||
|
|||
try an M4 x 0.7. I'm pretty sure that's the size.
|
#4
|
|||
|
|||
Not to be a smart-ass; but, have you tried
MARZOCCHI U.S.A. 28476 Westinghouse Place 91355 Valencia, CA - USA Tel: +1.661.257.6630 Fax: +1.661.257.6636 Also, there are a few suspension co's...especially in the mid-west that service the Zoks. Jon & Jim over at the Tech section of the GasGas site seem to always have some answers... Good luck. |
#5
|
|||
|
|||
Quote:
|
#6
|
|||
|
|||
Thanks guys. I do have speed bleeders on the ec250. I've hesitated getting them for the 300 since hearing that water can get by and into the forks. Probly not a big deal if I'm careful when washing.
__________________
'14 Beta 300rr '05 GG DE300 '03 GG EC250 '01 XR440 '09 FZ1 |
#7
|
||||
|
||||
Quote:
After much research, I found these. Chances of water getting is slim to none. http://www.systemtechracing.com/ |
#8
|
|||
|
|||
Ya, these are the ones I have too! They were'nt very expensive either. I think I'll go ahead and order another set. They're definetly convient. Just ordered another pair of ktm ones. No tax and free shipping thru usps.
__________________
'14 Beta 300rr '05 GG DE300 '03 GG EC250 '01 XR440 '09 FZ1 Last edited by flybars; 09-10-2012 at 04:31 AM. |
#9
|
|||
|
|||
I wonder if the size is the same for the 48mm CC marzocchi's
|
#10
|
||||
|
||||
48 Zokes are M4 thread just like the 45s and the WP forks. Measure to see if they will clear the bars when you turn the PFP adjuster, a discussed in other thread.
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
2011 EC250 fork bleeder size | forgiven | Enduro Suspension | 2 | 08-04-2012 09:56 PM |
Today's powervalve thread - loose bolt screws race | motogroove | Enduro Engine - 2 stroke | 3 | 07-29-2011 04:33 PM |
'10 Sachs fork bleeder thread size | Bailey28 | Enduro Suspension | 3 | 02-04-2011 03:29 AM |
Head orings | Brian VT | Enduro Engine - 2 stroke | 5 | 09-05-2008 11:49 AM |
Side panel mounting screws & grommets: 07 EC 300 | Gregarious | Enduro Chassis & Body | 2 | 02-19-2008 07:07 PM |