|
Enduro Engine 4 stroke (including EFI & Exhaust) 4 stroke engine, EFI, and exhaust discussion |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
FSE 450 rebuild, DR-Z parts?
Hi! I'm rebuilding my 450 engine. I have to change these parts:
OIL PUMP BODY OIL PUMP ROTOR RETRIEVABLE PUMP RING RETURN OIL ROTOR OIL PUMP COVER CENTRAL CRANKCASE GASKET CLUTCH COVER GASKET DISCS COVER GASKET IGNITION COVER GASKET CAM SHAFT DRIVE CHAIN CYLINDER GASKET CYLINDER HEAD GASKET I also need bearings, piston, cylinder regeneration, cam regeneration, clutch discs and tappets. And I have a few questions. Where should I order parts? My mechanic told me that he can buy parts for me and it will be 1500 euro which is lots of money. I heared that cilinder head is exactly the same as Suzuki DR-Z 400, is it true? OEM tappets would be 200 euro, tappets from DR-Z are much cheaper. And the bearings. Can I use others than OEM? Like SKF, KOYO or something? What's the difference? I need 6306C3 and 6303C3. Thanks. |
#2
|
|||
|
|||
I can say that drz cam chain fits 100% on my FSE450 from 2003. I replaced my tappets with OEM but I'm 98% sure they were the same size as my DRZ's (I own one of those too). Maybe look at getting parts form somewhere else because I only paid $80 for each tappet and DRZ ones were $112 each I bought from Scotties Dirt Bike Spares in Melbourne Vic Australia.
|
#3
|
|||
|
|||
I had a head rebuilt by scottys a year or so back and from memory it was only $200. That was for FSR 450 08
|
#4
|
|||
|
|||
I just got a new cylinder with piston and rings, both clutch gaskets, head gaskets tappet cover seal etc all for $500 to $600 from the guys at motocross center, try them they were very helpful and deliver fast.
|
#5
|
|||
|
|||
Does anyone know if i can replace head gasket with some other than original GasGas....bastards want 50 euros (55-60 dollars) for that gasket...
|
#6
|
|||
|
|||
Not to hijack the thread but I'm wondering whether the sensors and injector might cross over from Suzuki as well
|
#7
|
|||
|
|||
valve stem seals
Does anyone know of another brand of valve stem seals that will cross over to GasGas?
Due to the GasGas parts shortage I have run out of dealers to check. My street legal 07 450 with 1530 miles on the clock has started to smoke a bit sitting at red lights. I did a leak down test, and it was well within spec, it still runs strong. I suspect the seals.
__________________
04EC300 04Wild450 07FSR450 |
#8
|
|||
|
|||
Quote:
|
#9
|
|||
|
|||
Quote:
Thanks. Mike.
__________________
04EC300 04Wild450 07FSR450 |
#10
|
|||
|
|||
As far as I know an entire top end from a DRZ will fit but you will need the high compression piston or you will lose some power!
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
GG FSE 450 crank shaft and other parts [rebuild] | V1T0 | Enduro Engine 4 stroke (including EFI & Exhaust) | 8 | 10-27-2018 11:43 PM |
Top end rebuild | forgiven | Enduro Engine - 2 stroke | 9 | 12-05-2013 11:01 AM |
05 rebuild | brains | Enduro Suspension | 2 | 07-22-2008 08:54 AM |
Rebuild | steve | Enduro Engine - 2 stroke | 8 | 01-13-2008 03:06 PM |