|
|
#1191
06-20-2017, 02:11 AM
|
|||
|
|||
a video of the TT
<iframe width="560" height="315" src="https://www.youtube.com/embed/RGvpEvs_JV8" frameborder="0" allowfullscreen></iframe> https://www.youtube.com/watch?v=RGvpEvs_JV8
__________________
2003 txt250 Pro 2013 Ossa 280i 
|
|
#1193
06-21-2017, 02:09 PM
|
|||
|
|||
|
Looks very nice!
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar
|
|
#1195
06-22-2017, 12:05 AM
|
|||
|
|||
|
What did you do to your Gas Gas today?
It's a 2011 EC125 currently with the 125cc motor and not the 144 which i have to repair
This is how she looks right now  Gesendet von iPhone mit Tapatalk
__________________
4 strokes are only good for power generators 
|
|
#1196
06-22-2017, 07:33 PM
|
||||
|
||||
|
We had moments.
Fresh grips and throttle cable installed. Checked front brakes. Spongeeee.. Removed caliper to spread pads some and one slipped out. Found vines pushed in behind pads which was locking them up. Went to remove the pad pin with the caliper removed and was having no luck. Caliper back on and the old hit it with a hammer impact came out. Ended up rounding the allen head out. Should have been more patient and used lube and heat before getting frustrated and persevering. Then had to drill the pin out. Ended up a tad of center, but won't pose any significant issues. However only have a bees dick of thread left. Can drop a 9.5mm drill bit into a hole that should only be 9mm + 1mm thread. Don't have a 10x1mm tap to see how it cleans up, but will probably tap it bigger and drop an insert in as long as the depth isn't an issue. All this took much time, a few colourful words, and made a simple job overly complicated. The joy!
|
|
#1199
06-25-2017, 11:20 AM
|
|||
|
|||
|
What did you do to your Gas Gas today?
I put 2 hours of riding during a local race on my EC125.
The extra fly wheel works great, I could drop the rpm below idle without stalling the motor without making the motor slow or weak. The FMF works also great. I love my small gasser Gesendet von iPhone mit Tapatalk
__________________
4 strokes are only good for power generators
|
|
#1200
06-26-2017, 08:23 AM
|
|||
|
|||
|
I started it yesterday!
__________________
2011 EC200 (Current and favorite ride) Some Past Rides... 2012 XCF-W 350 (Revved to the moon) 2012 XC-W 300 Slavens Mule (Missile on wheels) 2006 EXC-W 400 (Awesome bike!)
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| DNF today | Pepperami | Enduro Chassis & Body | 6 | 09-18-2013 11:59 AM |
| Got my first GG today! | RonMexico | General Discussions & Announcements | 6 | 02-19-2011 12:39 PM |
| Went Riding Today and..... | coolum74 | Enduro Engine 4 stroke (including EFI & Exhaust) | 2 | 11-30-2008 01:12 PM |
| HELP! I tried to use my gasgas as a jet ski today! | sammyj18 | General Discussions & Announcements | 19 | 11-21-2008 08:01 PM |
| SHNF From Today | Boomhauer | Pictures & Videos | 13 | 10-30-2007 04:18 PM |
Linear Mode
