#91
|
|||
|
|||
Some more parts coming in bit by bit.I picked up some used protapers.
The Oem triples are rubber mounted, and when I disassembled the triples the rubber cones looked like new.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#92
|
|||
|
|||
Is this Race Removable?
Here is a better picture.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#93
|
|||
|
|||
The build is moving along. I ordered a suzuki oem top steering stem bearing so that is sorted.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#94
|
|||
|
|||
96-02 RM 250 Footpegs mounted on 84 RM 250.
I saw this listed on another forum without much detail so I though I would see if it would work because the stock 84 footpegs are very narrow. So, I pulled my frame out of my shipping box so I could drill out the peg mount holes before having the frame powder coated.
These are the stock pegs. These are the 98 RM 250 pegs with pins and springs. The pins are bigger on the 98 so you have to drill out the holes on the frame to 9.5mm which is a 3/8 inch drill bit. I used carbide bit and a Milwaukee hammer drill at super slow speed. You have to maintain pressure on the drill but barely rotate the bit, as long as you are getting long chunks of metal you are doing fine but if you are just getting metal dust, you are going too fast and you will ruin the bit. It took me about 6 minutes per each peg mount. Afterwards, the pins fit perfectly. Pegs bolted right up but I did have to file the brake side a little to clear a frame weld. 84 RM 250 peg and 98 RM 250 peg
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#95
|
||||
|
||||
Question why use a carbide bit on steel? Only bit you had??
__________________
'12 XC 200 TTX Sold '15 XC 250E Sale pending |
#96
|
|||
|
|||
I bought a drill press and a bit set. I know you are not supposed to use a carbide bit with a hand held drill or tool but I had trouble drilling the 1st hole out with a cobalt bit(maybe too fast rotation). I didn’t have any problem with the carbide bit. I suppose if you go slow and use lubrication to control the heat then HSS or Cobalt would work without any problem at all.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar Last edited by Moto7man; 07-07-2018 at 12:31 PM. Reason: Spelling |
#97
|
||||
|
||||
Good to hear! please continue.
__________________
'12 XC 200 TTX Sold '15 XC 250E Sale pending |
#98
|
|||
|
|||
Update
Big stuff is still at the powdercoaters. I just cleaned up some stuff to have it cad plated.
Here is the stuff after cleanup waiting to be cad plated. It took a while to get off all the rust I had to use a mini sledge to get the rear axle out. I thought it was impossible to clean up the threads. I bought a Snap On Thread Chaser RD7-18 which is a M16-1.50 thread pitch. It worked!
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#99
|
|||
|
|||
The new seat cover just arrived.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#100
|
|||
|
|||
Btw, I bought a small drill press and mounted it on the workbench last night.
It has a laser....
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
94 CR 250 Ground Up Restoration IMS Wide Ratio Transmission Issue | Moto7man | All Other Bikes... | 146 | 01-28-2018 05:57 PM |
1994 CR 250 Restoration featured on Dirt Bike Magazine Webpage | Moto7man | Pictures & Videos | 8 | 10-28-2017 09:12 AM |
Gas Gas Contact Jt 25 95 Restoration And Help | Eyetech | General Discussions & Announcements | 1 | 03-18-2016 03:33 PM |
2001 XC200 Restoration Project | Lincolnlock | Enduro Engine - 2 stroke | 19 | 04-22-2014 03:42 PM |
My Stomping ground | swazi_matt | Ride Reports | 10 | 03-02-2011 09:35 AM |