|
Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Jetting advice
I read every page of the jetting thread and I'm still scratching my head.Here is what I have in the bike now.
2007 EC 250 N1eg Needle 3rd clip from top 180 main 42 pilot #8 slide Racing an enduro 800-1000 ft temps so they claim 52* but race will start in the 40* and may stay that cold all day .This is the set up I run all summer plug is perfect and bike runs perfect.Would I be safe going with a 185 main and a 48 pilot there are some 6th gear fields and would rather not melt it down but don't want to be to rich just in case it does warm up.thanks Mike Last edited by Silver; 10-28-2009 at 09:22 AM. |
#2
|
|||
|
|||
What bike have you got Mike?
__________________
--------------------------- GG EC300 2007. |
#3
|
|||
|
|||
Some bike info would help good catch JD 2007 EC 250.Sorry I was making sure I had jetting correct and forgot the bike.
|
#4
|
||||
|
||||
Mike,
The 185 main looks good, but the 48 pilot may be too rich. A 45 pilot may be a better match to your current summer jetting. If you went with the 48 pilot, then you may need to back out the air screw to help lean the 0-1/8 throttle a bit. You should be receiving a PM from me.
__________________
Matt Current: 2009 Yamaha FZ1 Previous: 2001 GasGas TXT280, 2001 GasGas XC250, 2004 KTM 200EXC, 2007 GasGas EC250, 2007 Husqvarna SM610, 2008 Husqvarna WB165 |
#5
|
|||
|
|||
I think your jetting is good for hot dry summers, I have used your setup in Greece with no problems, but for cold weather racing I would go to a N1EF needle on the 2nd or 3rd clip with a #7 slide. The 42 pilot is just right, I have tried the 45 with a #8 slide and it has similar results with the 42 and #8 slide.
I use 178 to 180 main with the F needle with a 2% full synthetic oil mix, and have no issues after long transfer sections @ WOT. Try it, it gives a nice strong mid-range.
__________________
EC250 2008 Skid plate, rad braces, Fork bleeders Drz 400 Motard '03 (full spec) Yz 250 '06, KTM exc 250 '05, exc 250 '04, exc 250 '02 WRF250 '02, KDX 220 '98, DT200R '93 all sold |
#6
|
|||
|
|||
I'm stuck with this needle as i have no time to get another one.So have to come up with a setup around the N1EG needle. My thougts are to go with 185 main and 42 pilot and leave needle as it is set. I thought I had a 45 but do not so left 42 in and turned in air screw it is now out 1.5 turns.
Last edited by Silver; 10-29-2009 at 07:09 AM. |
#7
|
|||
|
|||
Do you have a #7 slide? It will help in the colder weather. IMHO I would go to a 182 main.
__________________
EC250 2008 Skid plate, rad braces, Fork bleeders Drz 400 Motard '03 (full spec) Yz 250 '06, KTM exc 250 '05, exc 250 '04, exc 250 '02 WRF250 '02, KDX 220 '98, DT200R '93 all sold |
#8
|
|||
|
|||
No I don't have a #7 slide.You think I will be safe with a 182.Temps look to be around 45 degrees mid day high 30's to start race.
|
#9
|
|||
|
|||
I think the 182 is O.K. together with a 1 to 50 oil ratio. The G nozzle has the same diameter as the LTR and CCK needles, which do not have any issues when driven WOT. I would play with air screw, I had it down to 1/2 out in such weather conditions with the #8 slide. You could also try raising the needle 1 clip as well. Ever bike is just that bit different so you have to try various set ups till you find which suites you.
Good Luck in your race
__________________
EC250 2008 Skid plate, rad braces, Fork bleeders Drz 400 Motard '03 (full spec) Yz 250 '06, KTM exc 250 '05, exc 250 '04, exc 250 '02 WRF250 '02, KDX 220 '98, DT200R '93 all sold |
#10
|
|||
|
|||
Thanks I went with the 185 42 pilot and air screw is 1 turn out rode it last night and seemed okay.Sounds like the race is going to be muddy so speeds may be slow.Weather man is not sticking his neck out to far on temps 51-37 degrees so I'm guessing some where in the middle.
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
06 250 Jetting Advice | Brian | Enduro Intake/Carburetion - 2 stroke | 4 | 08-28-2010 06:57 PM |
Advice, How much? | W8TSON | General Discussions & Announcements | 7 | 12-21-2009 03:30 PM |
Need advice please | gascanuck | General Discussions & Announcements | 2 | 12-15-2009 07:26 PM |
Advice Please | sbute | General Discussions & Announcements | 3 | 11-11-2009 07:04 PM |
WP advice | Brian VT | Enduro Suspension | 30 | 05-02-2007 07:13 AM |