#1
|
|||
|
|||
Reed valve
New to this forum. I can?t seem to find replacement reed valves. I have a 2011 EC300.
|
#2
|
||||
|
||||
Welcome to the forum.
Do you have the V Force 3 Reed block? |
#3
|
||||
|
||||
Welcome to the forum. Where are you located?
__________________
Anders "So you know, that you're over the hill when your mind makes a promise that your body can't fill" (Little Feat: Old Folks Boogie) 2015 EC200 Racing: TE bars, Rekluse Core Exp 3.0, 38mm Lectron & Ohlins S3 steering damper 2006 EC200: 2011 plastics, Rekluse Z-Start, revalved KYB forks & Scotts steering damper 1998 Bimota Supermono 1986 Duc Mille S2 1975 Guzzi sidecar hack 1961 Morini Corsaro 125 etc |
#4
|
|||
|
|||
Moto-Tassanari part #3P682M for replacement petals if V-Force 3.
__________________
Sponsors: http://www.evolutionsuspensionproducts.com/ http://www.sportbiketrackgear.com/ Blog: http://www.speedofarrival.com/ |
#5
|
|||
|
|||
Thanks for the response guys. I?m located in Hawaii. I just picked up the bike on Sunday. There?s a low to mid range gurgling, no hesitation. The best explanation I can give is if a car was running on 7 cylinders instead of 8. There?s no problem at WOT though. I opened up the carb and found 35 pj, 158 mj, and N8RW needle on the second clip. There?s spooge coming out of the muffler too. I ordered a JD jetting kit. I didn?t get to inspect the reed valves yet. It?s a vforce3 valve. Any info would be a big help. Thanks.
|
#6
|
||||
|
||||
Golly that's a small pilot and tiny mainjet. Never heard of that needle. Put the complete kit in and try it again.
__________________
'07 EC300 GG '14 TXT250 GG '? 496 CPI Cheetah RZ/RGV hybrid '22 765 Street Triple RS '21 XTrainer '69 Stinger T125 Suzuki '23 TRS 250RR (it's a Trials thing) |
#7
|
|||
|
|||
That?s what I said. I?m just waiting on my kit to arrive. That?s one disadvantage of living in Hawaii.
|
#8
|
|||
|
|||
I just bought reeds for the V-Force 3 in my 2011 EC250 from North Tahoe Motorsports on Ebay. Look them up. They've got a kit both with and without the gaskets. I'd highly recommend getting the one with the gaskets, as my gaskets were stuck on and removing them completely destroyed them. The ones on it (I assume stock) were a paper base, while the new ones seem to be a bit more like foam / rubber.
I'm not sure how shipping to Hawaii works, but it was very fast from Nevada to North Carolina. They've got piston and gasket kits, too. (I also ordered those at the same time). |
#9
|
|||
|
|||
Yeah I?ve been searching on eBay. I found one for $50 with free shipping to Hawaii.
|
#10
|
||||
|
||||
I recently replaced the reeds in my 07. They were wearing thin on the contact area but wouldn't have failed for some time. Have a look at them before you order.
__________________
'07 EC300 GG '14 TXT250 GG '? 496 CPI Cheetah RZ/RGV hybrid '22 765 Street Triple RS '21 XTrainer '69 Stinger T125 Suzuki '23 TRS 250RR (it's a Trials thing) |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Reed valve spacer... | motopsycho87 | Enduro Intake/Carburetion - 2 stroke | 6 | 08-03-2016 07:28 AM |
What reed valve in 2000 EC300 | Robert127 | Enduro Intake/Carburetion - 2 stroke | 4 | 02-16-2016 06:41 AM |
reed valve crossover mc 2000 | mikevancapel | Enduro Engine - 2 stroke | 3 | 01-21-2013 10:06 PM |
Vfrorce reed valve? | blanc | Enduro Intake/Carburetion - 2 stroke | 33 | 06-30-2012 07:12 PM |