|
Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Lets clear up clutch crossover
Lots of conflicting info on here as to what will and won't work on the GG as far as clutch replacement. Mine is starting to slip and was looking at brands/crossover options. Why don't you post what you are running and how it work and any mods you had to do. This is very interesting, but adds to the confusion-
http://www.barnettclutches.com/searc...n=301-48-10001 From what I have read looks like the best bet is to get the 3mm plates (GG is 2.7mm) with a thinner thrust washer (1.5mm, supposedly one off a Kawasaki will work, would someone post the exact model?) to make up the difference as the 2.7mm aftermarket are prone to breaking. How is this working out for folks?
__________________
2006 EC300, 2000 XR650R, 2003 EC250, 2001 EC200 (OK, the last two are really my sons). |
#2
|
||||
|
||||
Is it that hard to get GG plates in parts of the world? In the UK I just pick up the phone and any GG dealer has them.
|
#3
|
||||
|
||||
Quote:
when you're in there, check the rivets for the cush drive on basket... i switched to bolts and have had no problems.
__________________
07 ec300 was 00 xc200 now a 00 xc300. now parting out. 99 ec300 (now a pile of parts which are for sale) Stainless Cycle - Motorcycle Bolt Kits www.stainlesscycle.com Last edited by stainlesscycle; 11-01-2010 at 04:05 AM. |
#4
|
|||
|
|||
Quote:
Its a whole lot easier to turn loose of $50 for an aftermarket than $325 for an OEM kit.
__________________
2006 EC300, 2000 XR650R, 2003 EC250, 2001 EC200 (OK, the last two are really my sons). Last edited by kendunn; 11-01-2010 at 07:25 AM. |
#5
|
|||
|
|||
Quote:
__________________
2006 EC300, 2000 XR650R, 2003 EC250, 2001 EC200 (OK, the last two are really my sons). Last edited by kendunn; 11-01-2010 at 08:55 AM. |
#6
|
||||
|
||||
Luckily here the GG ones are the same as Honda etc in cost and certainly no where near $325 US, more like GBP 50 which is maybe $75
|
#7
|
||||
|
||||
Are you sure they are only 50 quid? If so I will get a set while I am back here! I cant believe something is actually cheaper in the uk!
__________________
06 Gas Gas FSE 450 USA 07 Gas Gas FSR 450 UK with motard and dirt wheels |
#8
|
||||
|
||||
Quote:
it was $44.99 for the whole deal.
__________________
07 ec300 was 00 xc200 now a 00 xc300. now parting out. 99 ec300 (now a pile of parts which are for sale) Stainless Cycle - Motorcycle Bolt Kits www.stainlesscycle.com |
#9
|
|||
|
|||
Quote:
I looked back at one of your earlier posts and you had a Suzuki part listed for the washer, but it seemed like the wrong one on the fiche. You had it listed as a 08211-22423 but looks like on the diagram a 09180-22045 is a closer match, is this correct? Can be seen at http://www.cheapcycleparts.com/model...emblies/115472
__________________
2006 EC300, 2000 XR650R, 2003 EC250, 2001 EC200 (OK, the last two are really my sons). |
#10
|
||||
|
||||
that washer 09180-22045 is 22.1x45x? 45mm o.d. is probably fine, but i can't find the thickness. if someone has a local friendly suzuki shop, you could probably stop by and measure it....
can't remember how i looked up that thrust washer... can you direct me to the old thread (can't seem to find it...) maybe it will refresh my memory.
__________________
07 ec300 was 00 xc200 now a 00 xc300. now parting out. 99 ec300 (now a pile of parts which are for sale) Stainless Cycle - Motorcycle Bolt Kits www.stainlesscycle.com |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Crossover Clutch Mastercylinder | leejames | Enduro Engine - 2 stroke | 2 | 07-21-2010 08:45 PM |
Clutch Basket Crossover | eff | Enduro Engine - 2 stroke | 13 | 03-07-2010 07:37 PM |
GG 125 clutch crossover | jayc | Enduro Engine - 2 stroke | 3 | 07-08-2009 11:51 AM |
125xc clutch crossover? | jayc | Enduro Engine - 2 stroke | 0 | 04-01-2009 12:23 PM |
250/300 clutch parts crossover | Skidad | Enduro Engine - 2 stroke | 5 | 01-09-2008 11:54 AM |