|
General Discussions & Announcements General Announcements, General Questions, e.g. What bike do I buy?, etc. |
|
Thread Tools | Display Modes |
#11
|
|||
|
|||
Hey Guys,
Almost there but I ran into a new problem. I reinstalled the carb and was ready to try starting but.....when I turn on the gas it immediately starts flowing out the overflow tube on the carb. What did I do wrong when I put it back together? Thanks, Sam |
#12
|
|||
|
|||
Your float isn't lifting the shutoff needle high enough.
You may have installed the tab thing upside down ? It's that little piece of sheet metal that the pin slides through. |
#13
|
||||
|
||||
The float is stuck allowing fule to flow freely. Try and tap the carb with a hammer or mallet lightly. If that does not free it up take it apart and make sure nothing it caught up.
__________________
2002 Gasgas EC250 (gone not forgotten) 2012 Ktm 300xc 2001 Gasgas EC300 Lifes journey is not to arrive safely at the grave in a well preserved body, But rather to skid in sideways totally worn out shouting holy cow what a ride !!!! |
#14
|
|||
|
|||
WHEW ok I can't thank you guys enough! I took apart the carb again resprayed everything with carb cleaner and blew it all out with compressed air...reinstalled and it worked like it should, MAN that carb is a pain to shoehorn in and out of position. After that I confirmed the bike was getting a good spark, and it took about 5 kicks but it started! I just let it sit and idle and revved it for a while, ill put all the plastic back on and take it for a ride in the morning. Ran fine little rough im guessing from the blown reed valve. Thanks again guys you saved my bike from the scrap heap!
Sam |
#15
|
||||
|
||||
AWESOME
Now wasn't that fun |
#16
|
||||
|
||||
Now you just stay away from still deep water and you will never have to go through that again, but sometimes its hard not to.
__________________
2002 Gasgas EC250 (gone not forgotten) 2012 Ktm 300xc 2001 Gasgas EC300 Lifes journey is not to arrive safely at the grave in a well preserved body, But rather to skid in sideways totally worn out shouting holy cow what a ride !!!! |
#17
|
||||
|
||||
glad to hear the good news....
i was absolutley sick to my stomach when my 300 went underwater and died..... first time I have ever done that. If it is a question at all now, I get off and walk the crossing first.
__________________
broken down over 60 slow rider.. |
#18
|
|||
|
|||
water and bearing = bad
I just did the same thing last week , I try to flush the water by remouving the spark pluk and kick kick kick. Re-start the bike and after 1 minute the engine seize. The main roller bearing seize on the crank godd the engine was only at idles. Cost me a rebuilt the engine over , Two bearing, seal and gasket. look at the bearing
Next time I will make sure that all water in out of the crankcase. Eric |
#19
|
|||
|
|||
Use the case drain!
|
#20
|
|||
|
|||
drain
I did not know about this drain until I rebuilt the engine
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
GNCC opener today | Skidad | Off Road Racer's Corner | 3 | 03-03-2009 03:48 PM |
yay my endurance came today | mountain thumper | Enduro Electrical & Wiring | 1 | 02-15-2009 08:11 PM |
Went Riding Today and..... | coolum74 | Enduro Engine 4 stroke (including EFI & Exhaust) | 2 | 11-30-2008 01:12 PM |
SHNF From Today | Boomhauer | Pictures & Videos | 13 | 10-30-2007 04:18 PM |
ISDE Starts Today! | Mark Berg - CPD | General Discussions & Announcements | 31 | 11-21-2006 09:27 PM |