Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Engine - 2 stroke

Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc.


Reply
 
Thread Tools Display Modes
  #1  
Old 07-13-2019, 01:41 PM
Kpo73188 Kpo73188 is offline
Member
 
Join Date: Feb 2018
Posts: 9
Default Noisy clutch while its engaged

Hi I have a 07 ec250, over the winter I did a complete rebuild of the engine, every bearing and seal was replaced, crank was rebuilt and the top end was replaced. I just recently got around to breaking the engine in, at first it ran great then it began loading up, long story short, I knicked the right side crank seal and it was burning oil. While I had the clutch back apart, i replaced the clutch basket with a Barnett basket that i had from a parts bike. Now that its running again I have a growling/bearing sound that goes away when I pull the clutch in. I used my new bearings with the basket, everything looked good on the Barnett basket. Just looking for some help on what to look for when I pull it back apart. Thanks


Reply With Quote


  #2  
Old 07-13-2019, 03:36 PM
gasgasman's Avatar
gasgasman gasgasman is offline
Super Moderator
 
Join Date: Jul 2006
Location: Pearland Texas
Posts: 4,594
Default

What you described sounds like "roll over" noise.
That's the transmission gears meshing together.

I would try a differed transmission fluid.
Reply With Quote
  #3  
Old 07-13-2019, 08:21 PM
Kpo73188 Kpo73188 is offline
Member
 
Join Date: Feb 2018
Posts: 9
Default

I've been running type f atf, I'll try a different fluid tomorrow and see if it helps.
Reply With Quote
  #4  
Old 07-14-2019, 06:02 PM
Kpo73188 Kpo73188 is offline
Member
 
Join Date: Feb 2018
Posts: 9
Default

I changed the oil with amsoil 10 40, and it did not change the noise at all. Any other ideas of what it could be?
Reply With Quote
  #5  
Old 02-06-2022, 03:04 PM
Tomi41 Tomi41 is offline
Member
 
Join Date: Dec 2021
Location: Magyarorsz?g Balaton
Posts: 1
Default

Quote:
Originally Posted by Kpo73188 View Post
I changed the oil with amsoil 10 40, and it did not change the noise at all. Any other ideas of what it could be?
Hello, the mistake of the clutch turned up?
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
2011 EC300 - Starter Won't stay engaged Timbre Enduro Electrical & Wiring 8 03-25-2015 09:55 AM
noisy exhaust hannesd Enduro Engine - 2 stroke 11 11-21-2013 04:55 PM
Noisy motor cangy Enduro Engine - 2 stroke 8 06-15-2013 02:39 PM
pop and bang and noisy pv gassergrant Enduro Intake/Carburetion - 2 stroke 8 06-27-2012 03:26 PM
Kick-starter won’t stay engaged sanderjavant Enduro Engine 4 stroke (including EFI & Exhaust) 1 10-09-2007 11:17 PM




All times are GMT -5. The time now is 01:04 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org