|
Enduro Electrical & Wiring Lighting, Ignition, Wiring, Plugs, etc. |
|
Thread Tools | Display Modes |
#11
|
|||
|
|||
when my reeds went it would bog out big time would not hit the power bands at all, but i doubt its that.
the stator plate will only go on in one position, if it was out it would run but pop and bang like a car or just have no power. there is a wood draft key on the crank just make sure it has not fallen out. im the same as you my knowledge is limited with electrics its a process of elimination try a old spark plug that you no works, also try a diffrent ht cap and lead. im not working tomorrow i will have a look at my bike and a wiring diagram and figure out what to test and how i did it |
#12
|
||||
|
||||
Ceres Phil, I'll try that as well, the plate did seem to be welded in place, but I didn't take much notice of the big oval shape at the top under the pick up, I kind of assumed it was all one peice. I hadn't put the bolt or washers in on the 10 and 5.00 positions when I took the picture.
__________________
GasGas Not Ass Gas.... No more KTM EXC'uses... www.scunnybikers.com @Ktmandy |
#13
|
||||
|
||||
Cheers for that Grant, wudruff key was in place, good point, the fly wheel can only go in one way because of that! Think I'm getting tired, should have thought about that
__________________
GasGas Not Ass Gas.... No more KTM EXC'uses... www.scunnybikers.com @Ktmandy |
#14
|
|||
|
|||
there is a blue wire that goes to the coils connected with a spade type connection, this is the live, if you have a circuit tester or the bulb trick,pt one end in it and one to earth kick it over and see what happens if you get sign of life the stator should be ok if not you have a
red/white black/red red green coming from the stator, im not sure if any are negitive but test these anyway the feed from the cdi is black and yellow this will conect to the blue LT test it and clean again pull all the cdi connections and clean and wd for now mate that all i can do |
#15
|
|||
|
|||
on the home page in the manaul section there is a basic wiring digram it would be worth a stdy
|
#16
|
||||
|
||||
Check the reeds. Forgot about that, it always escapes my feeble mind. No gaps = good, any gap = bad. Big gap and missing chips = terrible.
__________________
Phil (New bike pending...) |
#17
|
|||
|
|||
Since your this deep into it.. test the excitor coil of the stator. The sinle black covered post. This has the connector that goes up to your ignition/cdi. The spec should be the same as the KTM, below 14 ohm resistance between the two wires going to the cdi/ign bad. if you have a good hairdryer and the specs are lower of close to the 14, 14.4-15.5 good, heat the excitor coil up with a hairdryer and retest. Does sound like reed or powervavle not connected correctly after reassemble tho. Good luck!
__________________
Steve 16 Beta 350rr 04 KTM 525 sx/exc gone 03 KTM 625 sxc-rehab unit-did its job and now gone 03 GG 250 ec-gone 97 GG 250 ec Gone |
#18
|
||||
|
||||
Found the problem with the stator... A severed wire behind the plate!!!
One step closer, souldered it up, I have a big fat juicy spark... Now, all the dicking about with the jets and carbs, needs reverting, as it's drowning at the moment lol
__________________
GasGas Not Ass Gas.... No more KTM EXC'uses... www.scunnybikers.com @Ktmandy |
#19
|
||||
|
||||
Ill be home at dinnertime today if you need any help
|
#20
|
||||
|
||||
The s continues! At least, by the end of this, I'll pretty much have a brand new bike...
New fork seals New big end bearing New crank New small end bearing New wossner piston and rings New clutch plates I found the problem with the lack of spark, the wire on the back of the stator had snapped! So that's been replaced. Still wouldn't fire.... Taken carbs apart, cleaned and levelled the float using the great instructions on this forum. Still nothing! So took the reed block out, that was ok when I rebuilt the bottom end and top end and found this.....,, Don't know how or why it's smashed, maybe it got brittle??? So next question, I've got the part number, but only ones I can find are like ?60 or $100 plus P&P. Does anyone have a suggestion where to get a set from? When I bought this bike, my knowledge stopped at changing the oil and spark plug and cleaning the air filter.... Jesus! What I don't know now about bloody 2-strokes lol! Please help!! Part number ME25616041
__________________
GasGas Not Ass Gas.... No more KTM EXC'uses... www.scunnybikers.com @Ktmandy |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
EC 300 Gas Guzzler- Ideas?? | GasMCAndy | Enduro Engine - 2 stroke | 9 | 12-19-2011 04:39 AM |
any ideas help needed | leeroberts | Enduro Engine 4 stroke (including EFI & Exhaust) | 2 | 06-09-2010 06:54 PM |
bugger won't start, any ideas? | rupecopp | General Discussions & Announcements | 3 | 01-11-2009 07:33 AM |
looking for ideas?? | tub350 | Enduro Intake/Carburetion - 2 stroke | 4 | 08-18-2007 03:09 PM |