GasGas Riders Club Forum  

Go Back   GasGas Riders Club Forum > GasGas Enduro Technical Forums > Enduro Engine 4 stroke (including EFI & Exhaust)

Enduro Engine 4 stroke (including EFI & Exhaust) 4 stroke engine, EFI, and exhaust discussion


Reply
 
Thread Tools Display Modes
  #31  
Old 10-15-2021, 10:04 PM
AzWickedSS AzWickedSS is offline
Member
 
Join Date: Sep 2021
Posts: 25
Default

I have multiple injectors and no real change when putting a new one in. Maybe one of the sensors that communicates with the computer but I don't have a diagram of whats what. Coolant sensor, air sensor, etc thats not supplying the right amount of fuel/timing when hot. Not sure but its driving me a bit crazy


Reply With Quote


  #32  
Old 10-16-2021, 01:03 PM
MikelDuke MikelDuke is offline
Member
 
Join Date: Sep 2021
Posts: 3
Default

Hi
I am having similar issues to yours. Bike is very hard to cold start, it floods. When flooded, if I turn to start engine with the fuel pump disconnected, then it backfires and starts, and then I switch the fuel pump on again. I though it could be the fuel pressure regulator, which lets the pressure being too high, but it is not. Maybe it is the throttle sensor, which signal is too high, and the cdi commands fuel...I Will order a TPS and replace it, but the question is, hoy can I config the TPS range in the Kokusan CDI?
Reply With Quote
  #33  
Old 10-16-2021, 01:42 PM
AzWickedSS AzWickedSS is offline
Member
 
Join Date: Sep 2021
Posts: 25
Default

Have you checked your valves yet? If its hard to start cold valves have always been the culprit for me. My issue is it fires up cold easily but once warmed up and ridden it won't fire.

I have a new coolant sensor on the way and I pulled the ambient temp sensor last night that was caked in dirt so I'm hoping one or the other clears it up. I feel like it's a sensor that's either getting heat soaked and telling the computer to add to much fuel or vise versa.
Reply With Quote
  #34  
Old 10-16-2021, 01:46 PM
AzWickedSS AzWickedSS is offline
Member
 
Join Date: Sep 2021
Posts: 25
Default

Also the fuel injectors have been known to cause issues if anything clogs them the smallest amount. They can be had for like $10 online depending where you're located. Search IWP043. Got mine through Amazon since it was the quickest way for me.
Reply With Quote
  #35  
Old 10-16-2021, 04:27 PM
MikelDuke MikelDuke is offline
Member
 
Join Date: Sep 2021
Posts: 3
Default

Valve clearance is fine, I checked it, and the injector is new. I hace a spare of the water temperature sensor, the one located at the cylinder, but I do not know about the ambient temperature sensor, where is it?
Reply With Quote
  #36  
Old 10-16-2021, 04:31 PM
MikelDuke MikelDuke is offline
Member
 
Join Date: Sep 2021
Posts: 3
Default

By the way, the TPS I ordered is the MARELLI: PF1C/00
Reply With Quote
  #37  
Old 10-16-2021, 07:00 PM
AzWickedSS AzWickedSS is offline
Member
 
Join Date: Sep 2021
Posts: 25
Default

Air sensor is in the air box, right side near starter relay. You can see it barely if you remove the filter and can also access it by removing right side number plate on exhaust side. It's a small resistor type sensor, mine was covered up with dried dirt pretty good. Haven't put it back yet though and tried to fire it up. Was reading some ducati forums and its cause hard/ no stats with a lot of people. I don't know the PN off hand and hoping I can cross reference to something easily available.
Reply With Quote
  #38  
Old 10-16-2021, 07:45 PM
mekket mekket is offline
Member
 
Join Date: Aug 2020
Location: Estonia
Posts: 18
Default

Quote:
Originally Posted by MikelDuke View Post
Valve clearance is fine, I checked it, and the injector is new. I hace a spare of the water temperature sensor, the one located at the cylinder, but I do not know about the ambient temperature sensor, where is it?
The water temp sensor connected to the cylinder head should be responsible for turning on the radiator fan and as far as I know it has nothing to do with EFI.

Quote:
Originally Posted by AzWickedSS View Post
Air sensor is in the air box, right side near starter relay. You can see it barely if you remove the filter and can also access it by removing right side number plate on exhaust side. It's a small resistor type sensor, mine was covered up with dried dirt pretty good. Haven't put it back yet though and tried to fire it up. Was reading some ducati forums and its cause hard/ no stats with a lot of people. I don't know the PN off hand and hoping I can cross reference to something easily available.
https://www.roadraceperformanceshrop...erature-sensor Is this the sensor you are looking for? Ducati p/n 552.4.012.1A
Reply With Quote
  #39  
Old 10-16-2021, 09:31 PM
AzWickedSS AzWickedSS is offline
Member
 
Join Date: Sep 2021
Posts: 25
Default

That looks like the air sensor.

My bike didn't come with a fan, from what I read the temp sensor does communicate with the computer and can affect hot startingif it's not telling the computer the right readings
Reply With Quote
  #40  
Old 10-31-2021, 11:17 AM
mekket mekket is offline
Member
 
Join Date: Aug 2020
Location: Estonia
Posts: 18
Default

Have you made any progress? I took apart my starter motor. The brushes were quite worn and the bearing in the front of the starter is completely destroyed. I am still waiting for a new bearing and probably will be for a while because the only place I could find a suitable bearing was aliexpress and shipping from there takes ages. New brushes were easier to find. A brushplate from a DRZ400 fit perfectly and was around 10$
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
New GasGas owner 2009 450FSR AzWickedSS General Discussions & Announcements 0 09-14-2021 02:47 PM
2009 450fsr fuel pump wires schlitzy Enduro Engine 4 stroke (including EFI & Exhaust) 1 12-22-2020 03:13 AM
2009 450fsr sachs shock rebuild kit schlitzy Enduro Suspension 2 04-23-2019 06:04 AM
2009 450FSR valve specs schlitzy Enduro Engine 4 stroke (including EFI & Exhaust) 2 04-07-2016 08:46 PM




All times are GMT -5. The time now is 10:32 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2022, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org