Flywheel magnets on 2018 GasGas xc300

Jay Dizzle · #1 03-13-2023, 04:33 PM

I recently had a left side crank bearing go out on my 2018 XC300. This caused a piece of the magnet to break off my flywheel. I?m looking to do a complete top and bottom end job but wondering if it?s possible to just replace the magnet that broke on the flywheel instead of the entire flywheel assembly. Also looking to upgrade the stator since it was chewed up a little by the magnet. Any advice on where to get these parts including the piston, bearings, seals, and gaskets for engine would be awesome.

2018 GasGas xc300

SS109 · #2 03-13-2023, 09:41 PM

You can, in theory, fix the magnet but I can tell you it's not worth the trouble it would be.

As for parts, what country are you in?

gasgasman · #3 03-14-2023, 08:15 AM

CPD has a flywheel and stator kit for $300.
Or, you can go for the starter wet conversion for $600.
https://cpd.direct/pages/oem-parts-diagrams

Jay Dizzle · #4 04-02-2023, 10:16 AM

I?m in the US. Tucson, AZ. I?m a TRSofAZ member too. If I can?t fix the magnet, I?ll definitely check out that $300 one from CPD. I was quoted $560 from the local MotoCenter.

SS109 · #5 04-02-2023, 05:48 PM

Quote:

Originally Posted by Jay Dizzle

I?m in the US. Tucson, AZ. I?m a TRSofAZ member too. If I can?t fix the magnet, I?ll definitely check out that $300 one from CPD. I was quoted $560 from the local MotoCenter.

Damn, we got to get together and ride my club brother! Just got my Gasser back on the trail today. She's got a few minor things to address but she's a ripper!

Jay Dizzle · #6 04-03-2023, 11:53 AM

Quote:

Originally Posted by SS109

Damn, we got to get together and ride my club brother! Just got my Gasser back on the trail today. She's got a few minor things to address but she's a ripper!

Congrats on getting the Gasser back on the trail. Small world, I know who you are and ride your loop at Marana all the time. I?ll see you out there as soon as I get mine squared away.

SS109 · #7 04-03-2023, 12:00 PM

Quote:

Originally Posted by Jay Dizzle

Congrats on getting the Gasser back on the trail. Small world, I know who you are and ride your loop at Marana all the time. I?ll see you out there as soon as I get mine squared away.

Cool. I hope you get it going as the heat will soon be upon us!

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
2018 GasGas XC300	Kope618	Used Bikes	2	09-07-2022 10:10 AM
2018 EC 300 flywheel puller	eralha	Enduro Engine - 2 stroke	2	07-14-2020 07:18 AM
Flywheel puller 2018 XC300	TGM_OFFROAD	Enduro Engine - 2 stroke	4	10-15-2019 10:42 PM
2018 recall for flywheel raplacement?	GG221	Enduro Engine - 2 stroke	3	03-09-2019 09:26 AM
2018 GasGas XC300 Flywheel Weight	chunkysoup	Enduro Engine - 2 stroke	15	12-03-2018 02:27 PM