|
Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc. |
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
Fuel Leaking
Hi
Been out today and after dropping the bike (ahem!) it was leaking fuel out of the carb breather for a while. I'm going to take the carb off this weekend off and try and give it a clean, but any thoughts on what this might be or advice on cleaning up carb would be appreciated Thanks all! |
#2
|
||||
|
||||
Float level too high.
|
#3
|
||||
|
||||
you could also have something blocking your float needle..
__________________
07 ec300 was 00 xc200 now a 00 xc300. now parting out. 99 ec300 (now a pile of parts which are for sale) Stainless Cycle - Motorcycle Bolt Kits www.stainlesscycle.com |
#4
|
||||
|
||||
Very often they come with the Keihin carb float set too high. My '07 was fine but both my '00 and '03 would pee while on the sidestand. No big deal and an easy adjustment. Also, do a search on rerouting the vent lines, so they do not draw in water and dirt.
|
#5
|
||||
|
||||
the 2010 ec300 demo i have pisses fuel on the kickstand as well
__________________
trevor |
#6
|
||||
|
||||
Thanks guys
Is it just a case of bending the floats down a little then to try and stop this? I'm going to strip the carb down and use some carb cleaner over the weekend |
#7
|
||||
|
||||
See the Sticky at the head of this forum for the procedure.
|
#8
|
|||
|
|||
I guess its just the angle of the carbs, but they are really sensitive to level. Sometimes my carb would twist a little and would pee gas on the side stand. Like others have said, keep the float a bit lower than specs.
__________________
2006 EC300, 2000 XR650R, 2003 EC250, 2001 EC200 (OK, the last two are really my sons). |
#9
|
|||
|
|||
Do this guideline in the sticky also work for the newest generation of PWK.
I check my PWK 38 today - the float look totally different - almost only plastic no metal.Only the float assebbly tang is metal. My GG 300 2009 Nambo is leaking on the trailer. The float hight was 11mm - now I go to 14mm. I can't test it until now.My shock is in service.
__________________
Husqvarna TE 300 |
#10
|
|||
|
|||
I believe it was the fine dirt in the fuel tank
they blocked the float needle teflon surface after cleaning the tank no more leaking
__________________
Husqvarna TE 300 |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Leaking fuel lines. | Metalefty | Enduro Engine 4 stroke (including EFI & Exhaust) | 5 | 10-28-2009 09:50 PM |
One fork leg leaking after new seals - wrong way round? | stay_upright | Enduro Suspension | 17 | 08-07-2009 06:56 AM |
Cylinder gasket leaking. | GavGav | Enduro Engine 4 stroke (including EFI & Exhaust) | 2 | 05-18-2009 01:25 PM |
Fuel and AV Gas | kim | Enduro Intake/Carburetion - 2 stroke | 22 | 07-04-2008 11:06 PM |
Fuel range and fuel light | sanderjavant | Enduro Engine 4 stroke (including EFI & Exhaust) | 6 | 01-05-2008 02:35 AM |