|
Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Jetting Change
I made a one clip change to lean out my fuel as I was going through fouled plugs every 20 minutes or so.
Can you guys tell me if the pictures of the spark plug look good? Before they were very wet and totally black. Now they are light and dry... I want to make sure that it isn't too lean... http://www.rv7x.com/sparkplugs.htm Thanks!! |
#2
|
||||
|
||||
didnt look at the pics, but ideally they should be golden brown. think marshmallow.
__________________
03 ec250 hyde skidplate, cycra handguads, protaper contours "what? it seemed like a good idea at the time!" |
#3
|
|||
|
|||
Quote:
Well an update on this saga... as I noted in my first post that I made a clip change to lean it out, i then rode the bike for a good 30 minutes without issue. Took the pics that can be seen below. Plenty of crisp power except low end was kind of weak. Took it to the track today and my boy gets on it for no less than 2 minutes and the plug fouls!! We are going to tear down the carb and clean it out and probably buy some new jets. Anybody have any advice?? I'm certainly no expert on this stuff... 1st time having 2 stroke bikes in 15-20 years |
#4
|
||||
|
||||
i am no expert either, this is my first bike period, and im 17, but what ive heard is that there supposed to have a light golden color, whereas yours look darkish on one side and kindof wet.
__________________
03 ec250 hyde skidplate, cycra handguads, protaper contours "what? it seemed like a good idea at the time!" |
#5
|
||||
|
||||
is that a fresh plug? color doesn't look bad , but the ground strap looks beat up. is the electrode still square - or are the edges rounding?
__________________
07 ec300 was 00 xc200 now a 00 xc300. now parting out. 99 ec300 (now a pile of parts which are for sale) Stainless Cycle - Motorcycle Bolt Kits www.stainlesscycle.com |
#6
|
|||
|
|||
Quote:
Yep fresh plug with about 30 minutes of time on it. Electrode is still square. Funny thing is ... 24 hours later and 2 minutes into riding the plug fouls. Also... plenty of oil dripping from the exit of the silencer and runs the down the length of the pipe. I am running 42:1 whereas the previous owner ran it at 32:1 without problems until recently. I don't think I mentioned this earlier but it is a 125cc. Main jet is a 180 (manual says standard is 185). Got the clip on the needle on the 2nd notch from the top. Any suggestions? |
#7
|
||||
|
||||
I have a MC 250 that fouled plugs unless I road it "like I stole it" my problem was the float reset it and haven't put a plug in since.
__________________
02 EC 200 03 MC 250 88 VT 800 01 TXT 280 |
#8
|
||||
|
||||
I'd advise to make sure the float is set correctly. If it drools with the bike leaned over on the stand, it needs to be reset.
Next I'd look at the airscrew. Turn it in all the way and see how many turns out it is set. A good starting point is 1.5 turns out from fully seated. Check where your needle clip is. If it is in one of the lower settings, move it up. The needle will make the most dramatic changes in the way the bike runs, and it's simple to check. I wouldn't think your main jet would be the source of your issues unless you're always running around WFO. The pilot might be a bit rich, but if it's fouling out in a half an hour, I don't think that's it either. You could easily lean it out a couple of steps to see if you don't get good results with the others. There is a possibility that it's not jetting at all, but electrical, but with your description of the exhaust, likely not. Another possibility, and this is an ugly one: If your right side crank bearing is leaking, transmission oil will leak into the engine as it runs, creating lots of smoke out the exhaust, and the smelliest, nasty, gross scent ever, not typical two stroke smell. That would be your clue on this option.
__________________
Mike Sheetz OMRA #21AA What will I be riding next? Christini GG 300? '15 KTM 300 XC-W '08 EC 250 (Gone to new happy owner) Gran Prix Cycle LTR Suspension RB-Designs |
#9
|
||||
|
||||
Do what I did and check by riding not plug colour.
Put a 170 in and ride it on a flat open area, rev from closed to fully open, fast and slow to check for bogging etc. Change main to 185 and recheck. If nothing else you will get the feel for a too rich or too lean bike and you should be able to get it close by feel. I did this and found it to be very good in the determination of the main jet. All the best , Mark |
#10
|
|||
|
|||
Well I think I will start with a rebuild kit and then buy some jets as well. It was leaking gas from somewhere yesterday after the haul home and then when I put it up on the stand so hopefully it's just the float thing. We shall see!
Next question... I can't find a data plate on the bike itself. It is a 2003 125cc and I am assuming it is a MC125. Looks just like an EC but doesn't have any lights... Am I right in my assumption? If so... is the carb the same as the EC which is a Keihin 38mm PWK?? Thanks for all your help everyone!! |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
sprocket change will I need a new chain? | chucky | Enduro Chassis & Body | 13 | 06-08-2010 09:56 AM |
Hmm, should I change to the DE300? | BlueLghtning | General Discussions & Announcements | 10 | 01-18-2010 09:10 AM |
Head change | W8TSON | Enduro Engine - 2 stroke | 20 | 08-02-2009 09:17 AM |
Oil change... | FFRDave | Enduro Engine - 2 stroke | 14 | 06-29-2007 11:14 PM |
FMF Pipe Change | Dave Perna | Enduro Intake/Carburetion - 2 stroke | 1 | 03-12-2007 06:41 AM |