|
General Discussions & Announcements General Announcements, General Questions, e.g. What bike do I buy?, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Engine/pipe/radiator protection for 09 ec300
I have a brand new 09 ec300 on the way and I want to get some protection on the way as well. I've done some research and have some idea as to what I may want to get, but I'd love to hear some opinions or suggestions.
Here's what I'm thinking of going with. Pipe guard and skidplate Hyde combined guard and plate. I like the fact that it's light and may also have less friction than aluminum. Really costs no less than buying separate pieces. Radiator guards Maybe Scorpion? (They only list up to 08 though) Does Flatland make a guard for 09? Does 09 still use the same radiator as KTM? I want full guards, not just frame, since we get deep into the sticks sometimes. Handguards I've been happy with my Cyrcra's so I may just move them over to the GG, but I'm open to suggestions. |
#2
|
||||
|
||||
I have the Hyde Skid Plate/Pipe Combo on my 2007 and I like it. It's protective, it's quiet, and it provides good coverage. So far, no problems with mud buildup or breakage. I also hear they are coming out with a new design in the next 30 days (contact them). I've learned not to care for aluminum plates with solid mounts: They stiffen the bike, adversely affect the handling, and vibrate a good bit (I eventually break the mounts due to excessive vibration).
Radiator guards: Bulletproof Designs guards are good (have them) but I'm going with Unabiker guards (another thread) as they look cool and seem to have a good design. Handguards: I have Cycra and they are fine, I have Acerbis wraparounds and they are fine. I would just go with what you already have! As a side note, try to get an aluminum throttle tube with a bearing that works with handguards as they have a nice consistent "feel". Good Luck! Eric
__________________
2018 GG 300 GP 2014 GG 300 Racing E 2002 ATK 605 Dual Sport 2003 KX/KDX 220 hybrid 2021 Kawasaki KRX 1000 Trail Edition 1974-86 Vintage Can Ams, SWMs, Puchs, etc. |
#3
|
||||
|
||||
The Scorpion radiator braces are very nice. They do not interfere with the radiator schroud fitting and appear to be bullet proof. We put a couple of sets on the 2011 models but I don't know if they will fit the 09 or not.
|
#4
|
||||
|
||||
i also have the hyde, and the only reason it picks up dirt around the pipe is because i havnt taken the time to put foam there. they arnt terribly difficult to remove and put back on, but the forward mount was not the correct width when i bought it. i bent it around some and didnt worry about it, and it hasnt been a problem.
__________________
03 ec250 hyde skidplate, cycra handguads, protaper contours "what? it seemed like a good idea at the time!" |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
New 2010 EC300 Engine Noise (falling revs) | Jakobi | Enduro Engine - 2 stroke | 11 | 11-16-2010 06:41 PM |
EC300 engine noise | fittal | Enduro Engine - 2 stroke | 6 | 11-03-2010 09:42 AM |
Rib Protection | Noel | General Discussions & Announcements | 7 | 05-03-2010 11:59 PM |
Need Protection | biggstr6 | General Discussions & Announcements | 10 | 10-08-2009 09:37 PM |
Chest/Body Protection | sammyj18 | General Discussions & Announcements | 9 | 07-14-2008 03:18 PM |