|
|
|||||||
| Enduro Chassis & Body Enduro Frame, Plastic, Brakes, Bars, Controls, wheels, tires, sprockets & gearing. |
 |
|
|
Thread Tools | Display Modes |
|
#1
03-27-2013, 04:58 PM
|
||||
|
||||
Rear brake pad pin
I want to replace my quick release pad pin, with a threaded type. Does anyone know if there are many different types?
I found a set that are threaded-old moose racing for rmx- wondering if theses might work? Bike is at home-otherwise i would just try them. Thanks 
Last edited by adv rider; 03-28-2013 at 12:27 AM. 
|
|
#2
03-27-2013, 06:07 PM
|
||||
|
||||
|
Not sure on the rm pin. I just order the ebc pads with the pin in the package every time I get pads. You can rotate your stock pin 180 and place the clip back in to wear on the opposite side if it's notched.
__________________
2018 EC 300 
|
|
#3
03-27-2013, 08:49 PM
|
||||
|
||||
|
threaded pin
No it's not notched- The bike is new , and in the first 5 minutes the clip came out. Which allowed the pin to come out partially and the pad dropped down and locked up my wheel.
I was lucky that I was at my truck just as it locked up, I safety wired the pin in place. But I would feel better with a threaded one. I am home now-so will try the rm pin shortly- The pin threaded right in! I feel much better now. Since it was a 2 pack, I have 2 extras- 1 threaded, 1 quick release Also does anyone know if the clutch/brake lever cross over to any other brands? Last edited by adv rider; 03-28-2013 at 01:18 AM. Reason: tried pin/ other ?
|
|
#4
03-28-2013, 02:19 AM
|
||||
|
||||
|
Quote:
Sent from my OMNIA7 using Board Express
__________________
Anders "So you know, that you're over the hill when your mind makes a promise that your body can't fill" (Little Feat: Old Folks Boogie) 2015 EC200 Racing: TE bars, Rekluse Core Exp 3.0, 38mm Lectron & Ohlins S3 steering damper 2006 EC200: 2011 plastics, Rekluse Z-Start, revalved KYB forks & Scotts steering damper 1998 Bimota Supermono 1986 Duc Mille S2 1975 Guzzi sidecar hack 1961 Morini Corsaro 125 etc
|
|
#5
03-28-2013, 04:33 AM
|
||||
|
||||
|
The brake lever is also a Honda CR. The clutch lever has no cross over but I run a GG trials lever. It's a shorty. With Bark busters you never really break them. If your bike is an 11 or newer the rear pads are the same as 08 Yamaha yz 450 and the front are still early 2000 Honda CR.
__________________
2018 EC 300
|
|
#6
03-28-2013, 03:50 PM
|
||||
|
||||
|
brake parts
Thanks for the parts crossover info. i don't have bark busters yet, and i worry about the levers- i am travelling 250 mi to go riding next week. So it's good to know what works.
I will get a spare clutch lever from my local dealer
|
|
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Rear brake | wmcpb04 | Enduro Chassis & Body | 0 | 11-08-2012 04:35 PM |
| Using the rear brake | IDAHOSPUD | General Discussions & Announcements | 13 | 10-09-2012 05:49 PM |
| Rear brake S***s! | bondo | Enduro Chassis & Body | 33 | 01-04-2012 09:41 PM |
| FSE 450 rear brake... | Vinny | Enduro Chassis & Body | 4 | 06-09-2011 07:52 PM |
Linear Mode
