GasGas Riders Club Forum  

Go Back   GasGas Riders Club Forum > GasGas Enduro Technical Forums > Enduro Engine - 2 stroke

Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc.


Reply
 
Thread Tools Display Modes
  #1  
Old 06-11-2014, 10:37 AM
jprizz jprizz is offline
Member
 
Join Date: May 2014
Location: Temperance, MI
Posts: 59
Default Ec300 clutch assembly position

I needed to replace my kick start shaft so I disassembled my clutch to do so. Then I read this in the shop manual:
Note:
The clutch hub has an assembly position with respect to the primary shaft. Mark the position using a permanent marker on the grease ring.


So how important is this? Since I didn't mark it is there any way to determine the assembly position? Is it because its balanced or something?

Thanks,
-Josh


Reply With Quote


  #2  
Old 06-12-2014, 03:19 PM
motopsycho87 motopsycho87 is offline
Senior Member
 
Join Date: Jun 2013
Location: Suffolk, UK
Posts: 900
Default

I can assure you mine has been removed and refitted so many times that the chances of it being in the "correct" position are as many splines are on that shaft. It runs fine
__________________
2006 EC300 Enduro - Ignitech CDI - 38/NECW#2/165 FMF gnarly, FMF shorty, .50 front 5.7 rear

2016 RM-Z450
Reply With Quote
  #3  
Old 06-12-2014, 03:50 PM
Jakobi's Avatar
Jakobi Jakobi is offline
Super Moderator
 
Join Date: Oct 2010
Location: Australia
Posts: 7,996
Default

Quote:
Originally Posted by motopsycho87 View Post
I can assure you mine has been removed and refitted so many times that the chances of it being in the "correct" position are as many splines are on that shaft. It runs fine
That instruction in the manual spun me out too. I couldn't get my head around any particular reason why it was important. I figured it was something lost in translation regarding the position of the lock washer tab. *shrugs*
Reply With Quote
  #4  
Old 06-12-2014, 04:25 PM
desertgasser300 desertgasser300 is offline
Banned
 
Join Date: Feb 2011
Location: Hot A@% desert AZ.
Posts: 1,872
Default

There's a manual???

Sent from my SGH-T999L using Tapatalk
Reply With Quote
  #5  
Old 06-17-2014, 06:01 PM
jprizz jprizz is offline
Member
 
Join Date: May 2014
Location: Temperance, MI
Posts: 59
Default

Thanks guys, I just went and put it back together because I needed to go riding. Didn't have any issues with it.

I found the manual in the General Discussion thread - its a sticky too.
__________________
-Josh

2009 EC300 Six Days
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Is clutch basket position critical on re-assembly hillbilly Enduro Engine - 2 stroke 1 04-06-2012 07:32 AM
2008 EC300 clutch assembly position mwoody98 Enduro Engine - 2 stroke 0 03-13-2012 09:52 PM
Looking for a clutch master cylinder assembly... SpeedyManiac General Discussions & Announcements 5 05-09-2008 07:06 PM




All times are GMT -5. The time now is 04:34 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2022, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org