![]() |
|
Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc. |
![]() |
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
![]()
A while back, I posted a link on how to set your float level.
I finally found it after a long search. Here it is again for those that need to have their's reset.. http://www.dirtridersinternational.c...?TOPIC_ID=2292 Last edited by gasgasman; 08-25-2007 at 09:08 PM. |
#2
|
||||
|
||||
![]()
For some reason the photos won't come up.
Here they are in the order that they appear in the instructions. ![]() (Float assembly pivot pin not shown.) ![]() (Fuel inlet needle shown with Viton (rubber) tip. The Viton is used to isolate the fuel inlet needle from vibration and to create a better seal against the fuel inlet valve seat.) ![]() ![]() |
#3
|
|||
|
|||
![]()
The first link no longer works.
I have checked and adjusted float level on other carbs, so could someone post some basic instructions with dimensions? Thanks, Josh |
#4
|
||||
|
||||
![]()
Try this http://www.keihin-us.com/am/_media/pdf/slide_valve.pdf
Float height is mentioned on the right.
__________________
'05 Gas Gas 300 '97 Aprilia Pegaso 650 '99 KTM 200 '95 ish XR630 (died many times in Oz) |
#5
|
|||
|
|||
![]() Quote:
of the float as shown in the picture. |
#6
|
|||
|
|||
![]()
Hi can anyone advise me on the correct float height for my year 2000 ec 300.
|
#7
|
||||
|
||||
![]()
16mm to the best of my knowledge.
__________________
07 ec300 was 00 xc200 now a 00 xc300. now parting out. 99 ec300 (now a pile of parts which are for sale) Stainless Cycle - Motorcycle Bolt Kits www.stainlesscycle.com ![]() |
#8
|
||||
|
||||
![]()
Sounds right, but a rule of thumb is to have the seam in the float parallel to the carb body.
__________________
2004 GasGas DE250 |
#9
|
||||
|
||||
![]()
I set the floats on my GG by simply tilting the carb and closing the float gap until it stopped puking fuel at a 20 to 30 degree angle, then took a test ride and checked it at W/O.
May sound stupid bit it works. A friend has a 09 that still drools when on the side stand. |
#10
|
|||
|
|||
![]()
Do this guideline also work for the newest generation of PWK.
I check my PWK 38 today - the float look totally different - only plastic no metal. The GG 300 2009 Nambo is leaking on the trailer. The float hight was 11mm - now I go to 14mm. I can't test it until now. My shock is in service.
__________________
Husqvarna TE 300 |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
EC300 Idle Revisited. | Ud_luz | Enduro Intake/Carburetion - 2 stroke | 35 | 01-07-2011 07:39 PM |
Rear wheel spacers revisited. | Ud_luz | Enduro Chassis & Body | 9 | 09-13-2010 08:01 PM |
Zokes oil level? | jostby | Enduro Suspension | 2 | 06-20-2009 11:29 AM |
Fork oil level ? | Brian VT | Enduro Suspension | 4 | 03-10-2009 08:57 PM |
WP Fork Oil Level | MattR | Enduro Suspension | 11 | 08-02-2006 10:40 AM |