|
Enduro Suspension Tuning & maintenance of Enduro forks, shocks, etc |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Confirm Torque Specs for Forks/Linkage for 2018+ EC300?
Have my owners manual and found what I think is the upper and lower triple clamp torque specs, but would like to confirm before tightening them down. (See attached). Looking at the Upper and Lower flange torque specs.
I like to loosen and retorque my forks after each ride (drop ) to make sure everything is all aligned up correctly - torque the bolts to the correct torque is also important. Also in the manual it says "Link", which I assume is linkage, and all the nuts are at 80nm - This sounds about right, but would like to confirm before bringing down the torque. |
#2
|
||||
|
||||
|
#3
|
|||
|
|||
Thanks for sharing the workshop manual, but i can't find anything about the suspension in it, seems to be only engine related.
|
#4
|
||||
|
||||
Quote:
__________________
Anders "So you know, that you're over the hill when your mind makes a promise that your body can't fill" (Little Feat: Old Folks Boogie) 2015 EC200 Racing: TE bars, Rekluse Core Exp 3.0, 38mm Lectron & Ohlins S3 steering damper 2006 EC200: 2011 plastics, Rekluse Z-Start, revalved KYB forks & Scotts steering damper 1998 Bimota Supermono 1986 Duc Mille S2 1975 Guzzi sidecar hack 1961 Morini Corsaro 125 etc |
#5
|
|||
|
|||
What are the specs for your 2015 out of curiosity ?
|
#6
|
|||
|
|||
Yes upper and lower flange is triple clamps and link is linkage.
|
#7
|
||||
|
||||
There is a torque table in the workshop manual for every bolt on the bike.
__________________
2018 EC 300 |
#8
|
||||
|
||||
Upper: 15 Nm
Lower: 11 Nm
__________________
Anders "So you know, that you're over the hill when your mind makes a promise that your body can't fill" (Little Feat: Old Folks Boogie) 2015 EC200 Racing: TE bars, Rekluse Core Exp 3.0, 38mm Lectron & Ohlins S3 steering damper 2006 EC200: 2011 plastics, Rekluse Z-Start, revalved KYB forks & Scotts steering damper 1998 Bimota Supermono 1986 Duc Mille S2 1975 Guzzi sidecar hack 1961 Morini Corsaro 125 etc |
#9
|
|||
|
|||
Bumping this up - I have my front wheel off and want to torque up the pinch bolts for the axel. Do you think it is the "foot fork" at 15nm?
|
#10
|
|||
|
|||
Yes, 15nm for the pinch bolts.
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
2018 Ec300 Jetting Specs | Mud-Ectomy | Enduro Intake/Carburetion - 2 stroke | 53 | 11-17-2021 01:48 PM |
Torque specs :( | NM_GG_Rider | Enduro Chassis & Body | 9 | 07-01-2021 05:35 AM |
2018 EC300 Linkage Slop | emepher | Enduro Suspension | 7 | 07-17-2018 09:01 AM |
torque specs | kstreet | Enduro Engine - 2 stroke | 1 | 01-28-2011 07:05 PM |
Torque Specs | steve | Enduro Engine - 2 stroke | 8 | 02-26-2008 09:30 PM |