|
Other GasGas Bikes/Quads Trials, Pampera, Wild HP, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
i have a GasGas wild Hp300!!
i have a gasgas wild hp300 for a few days, i'm check it complete to find any defects, what i find is a broken brake disc of the rear. its broken on 8 places . the bearings from the rear axle need to replaced, and the house of the hydraulic clutch what is mounted on the engine. what it is going to cost totally is around the 250 euro's ( i guess)
pictures you can find on: http://quadforumbenelux.com/viewtopic.php?f=32&t=32992 its a dutch site because i'm from the netherlands I've buy a compression meter to check out the compression of the gasgas, it is now 1:12 but i do not know wat it is original without any adjustments. is there someone here who no's the original compression? Sorry for my bad english i'm trying to do it that good as possible Thanks! |
#2
|
|||
|
|||
nobody?
|
#3
|
||||
|
||||
i would assume the compression should be about 190-195psi in perfect condition. someone correct me if i'm wrong???
__________________
07 ec300 was 00 xc200 now a 00 xc300. now parting out. 99 ec300 (now a pile of parts which are for sale) Stainless Cycle - Motorcycle Bolt Kits www.stainlesscycle.com |
#4
|
|||
|
|||
hmm oke, i thought that it whas that high when the block is heavy tuned. 190/195psi is here 1:13,44....
|
#5
|
|||
|
|||
Both my bikes have 175psi +/-. one has had the squish machined. I wouldn't think the 300 would be much different. I don't know if there is a published specification for the compression ratio.
You could probably use the clutch slave cylinder from a bike engine. Watch ebay as they get parted out often. There aren't near as many ATVers on this site. Have patience and others will eventually chime in
__________________
jeff '00 XC250 (mine) LTS front and rear suspension, power valve cover, carb jet kit and rear chain glide, RB Designs head mod, BRP tall triple clamp, backyard foot-peg lowering conversion. '04 EC250 (the kids) (he can do his own mods haha!) |
#6
|
|||
|
|||
thanks for the advice, i've found a dealer who's building gasgas 300 blocks in his homemade cross quads. it's 4 km from here ( 4000 meters and can order parts by gasgas.
What about the clutch slave cylinder, its exactly the same as that one from the gasgas ec300 |
#7
|
|||
|
|||
The slave cylinder should be the same for 250 and 300. I'm unsure of the 125 and 200.
__________________
jeff '00 XC250 (mine) LTS front and rear suspension, power valve cover, carb jet kit and rear chain glide, RB Designs head mod, BRP tall triple clamp, backyard foot-peg lowering conversion. '04 EC250 (the kids) (he can do his own mods haha!) |
#8
|
||||
|
||||
200-250-300 is all the same, 125 is a different slave cylinder
|
#9
|
|||
|
|||
oke thanks , the bearings are a strange size to find... i hope i have it for next week becuase i have a race on 4 sep.
|
#10
|
|||
|
|||
Did you find axle bearings? I replaced mine with bearings from a Honda TRX250 Recon. I put two bearings in each side for a total of four. It took a little mod, but they have been working fine for awhile.
If you can not find the rear disc, a disc off of a late model KTM rear wheel (530EXC as an example) will work. You just need to drill the holes out to the same size as your old disc. There is a multitude of discs available for the KTM so you have a lot more options available if you do that. I found the KTM original part to be my best deal here in the U.S. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
wild HP 300 rebuild | case-racing | Other GasGas Bikes/Quads | 16 | 05-25-2011 02:52 PM |
Wild HP300 Fuel Tank | Richardcranium | Other GasGas Bikes/Quads | 1 | 03-18-2010 06:26 PM |
07/08 Wild HP details | barkeater | Other GasGas Bikes/Quads | 4 | 12-28-2007 05:04 PM |
wild 300 and other 300's | WILDGASGAS300 | Enduro Engine - 2 stroke | 1 | 10-26-2007 11:58 AM |
Wild 300 Hp | PA300HPWILD | Enduro Electrical & Wiring | 0 | 10-09-2006 06:59 AM |