|
Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Metal on metal sound when O-rings from exhaust wear out.
Hi Everyone,
I have fixed this 4 times in the past year.. The o-rings SLIGHTLY wear and I get a metal Buzz sound from the front pipe. If I put my boot on the pipe it stops of course and if I change the O-rings it stops... So I know the problem and how to fix it, but it should not be happening every 4 -6th ride and Is there a known issue with this? I ask because Gofasters has a replacement exhaust spigot.. Seems ODD to have one on the site like that? |
#2
|
|||
|
|||
McMasters has better viton o-rings that hold up much longer. I can't remember the size, but GMP knows what size they are. Or you can do a search here on them. I would look it up but I'm on my phone and it will take to long.
|
#3
|
||||
|
||||
Another option is to clean everything really well and use high temp RTV to seal the connection.
|
#4
|
|||
|
|||
This is what I'm trying next - worked great on my KDX.
|
#5
|
|||
|
|||
Ps, I use the rtv sealent I have used red, and nine I'm trying the copper..
|
#6
|
||||
|
||||
Check the alignment of the pipe, and also the lower pipe mount. I've found if the lower mount is flogged out it allows too much movement of the pipe which causes too much wear on the seal.
As above Viton o-rings and RTV Red. I was going through this every couple rides until I fixed the mounts up. Since then I can really scrag out the o-rings. |
#7
|
|||
|
|||
nail a stump just right and it should make the fit nice and tight to stop that buzzing
__________________
jeff '00 XC250 (mine) LTS front and rear suspension, power valve cover, carb jet kit and rear chain glide, RB Designs head mod, BRP tall triple clamp, backyard foot-peg lowering conversion. '04 EC250 (the kids) (he can do his own mods haha!) |
#8
|
||||
|
||||
One pipe buzzed & one didn't. the pipe that didn't was twisted & the front mount was twisted to get the bolt in. More tension, but pain in arse to fit.
I ended up fitting some extra springs on the manifold. buzzing stopped on straight pipe. (+ viton & sealant) |
#9
|
||||
|
||||
I replaced the lower pipe mount with some yz parts. This has seemed to make the biggest difference. I also switched the exhaust spigot out for a LTR unit as mine was quit worn. I will see. If I can find the part numbers when get home next week.
__________________
2018 EC 300 |
#10
|
|||
|
|||
Thanks Everyone!! Ill be racing this weekend and after Ill look at everything posted!!
Thank you all greatly for your help! |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
High pitch Squealing from exhaust and exhaust flange????? | Scar13 | Enduro Engine - 2 stroke | 5 | 02-11-2012 11:32 AM |
Metal shavings in oil | mikemoto | General Discussions & Announcements | 4 | 08-28-2011 10:51 PM |
Large piece of metal from drain hole??? | desertgasser300 | Enduro Engine - 2 stroke | 16 | 06-22-2011 08:12 PM |
EC250 exhaust O rings? | BIG TOOL | Enduro Engine - 2 stroke | 17 | 09-10-2010 04:31 AM |
Mothers Metal Polish | Boomhauer | Enduro Product Reviews | 3 | 06-23-2007 07:02 AM |