|
Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
OEM clutch
What brand is the OEM clutch for gas gas ,especially friction plates ? I have one from Adige (italian brand) and i think ,that this is the oem gas gas clutch .
|
#2
|
||||
|
||||
It's a honda clutch I think cr 250 not sure what year
|
#3
|
|||
|
|||
My friend said me ,that this is the OEM clutch .He has seen the same discs in brand new gas gas .
|
#4
|
|||
|
|||
Honda Clutch Pack Conversion
See post #42 and #46 on this thread. Honda fibers are 2.98mm and the GasGas Fibers are 2.75mm. (2011 GasGas)What are the measurements for your aftermarket plates?
http://www.gasgasrider.org/forum/sho...tch+conversion
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#5
|
|||
|
|||
My plates are around 2,80mm (haven't micrometer) .I bought it from gas gas dealer and my question is whether these are
the OEM(Original Equipment Manufacturer ) gas gas plates .I'm almost sure they are .I think ,that the oem plates will work better than aftermarket . Last edited by Getoviq95; 02-11-2018 at 08:16 AM. |
#6
|
|||
|
|||
Quote:
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#7
|
|||
|
|||
Adige lists clutch plates for older Gassers and Hondas, try their catalog link below.
http://www.adige.eu/public/ENG/catalog/result.asp
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
how to fix MOST clutch problems + cr250r clutch conversion. | stainlesscycle | Enduro Engine - 2 stroke | 70 | 10-26-2020 04:06 AM |
Hydraulic clutch actuator and clutch rod | budryzer | Enduro Engine - 2 stroke | 6 | 07-25-2015 07:44 PM |
Auto clutch Install, Rekluse or S3 Clutch Basket? | Moto7man | General Discussions & Announcements | 49 | 11-24-2013 12:41 AM |
Clutch lever doesnt release clutch as soon as motor starts | cal_tony | Enduro Engine 4 stroke (including EFI & Exhaust) | 5 | 05-19-2012 08:59 AM |