|
General Discussions & Announcements General Announcements, General Questions, e.g. What bike do I buy?, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Used EC250 Questions
I looked at a used '04 EC250 today, and have a couple questions.
1) There appears to be an extra set of holes in the top triple clamp so that the bar mounts may be moved forward. Is this normal for this bike? I haven't read anything about this feature, so that's why I'm asking. 2) When I push down to compress the forks, and then release, there is a "clunk" that can be felt through the handlebars right when the forks return all the way to their uncompressed position. Does this mean anything? I've never felt that on other bikes. |
#2
|
|||
|
|||
Not sure about Question 1, though my top triple clamp is slotted so maybe
Question 2. Sounds like loose headset bearings. Someone with more experience will chime in, but that's a start for you Adam
__________________
Adam 2006 FSE450...Gone 2011 EC300e Sunshine Coast, Queensland Australia |
#3
|
||||
|
||||
Q1. Yes this is normal. The top clamp has two positions.
Q2. Not sure based on your description. Maybe loose steering head bearings as noted above.
__________________
2004 GasGas DE250 |
#4
|
|||
|
|||
Cool, glad about the ability to move the bars forward, as it feels too rearward for me where it's at now (used to KTM ergos).
If the clunk is from loose steering bearings, is this because the steering nut is loose, or the bearings are worn? If it is worn bearings, is this difficult or expensive to fix? I do all my own bike work, but I've never messed with headset bearings. Do they need to be pressed out with a special tool? |
#5
|
|||
|
|||
FYI, I called my local suspension guy (John Curea at MX-Tech) and he said that it sounds like the forks are low on fluid, probably from leaking seals. He said he has a KTM in his shop right now that was doing the same thing. The forks did feel rather bouncy when I test rode it, so he's probably right on.
The other thing about this bike is it may need to have the silencer repacked. It's an FMF TurbineCore. Is this hard to do on this type of muffler? I've repacked a conventional FMF muffler in the past (with the screen spark arrestor), and it wasn't too bad. |
#6
|
||||
|
||||
It's really easy to repack the silensor. I use the Moose cartidge and is as easy as pulling it apart, remove the old one, clean it and slide the new one on.
If it is the bearing it may be just in need of tightening, however if it has been that way a while and ridden the bearings may be shot.
__________________
2004 GasGas DE250 |
#7
|
||||
|
||||
Make sure the front wheel is installed properly. If not properly put back together after a front wheel removal, you can have space between the spacer and fork leg which will cause the wheel to slide back and forth on the axle. Strange, but true, I've done it. It makes a clunk sound when compresssing the fork.
__________________
Mike Sheetz OMRA #21AA What will I be riding next? Christini GG 300? '15 KTM 300 XC-W '08 EC 250 (Gone to new happy owner) Gran Prix Cycle LTR Suspension RB-Designs |
#8
|
|||
|
|||
Quote:
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
EC250 Questions from a new member | Stef | Enduro Engine - 2 stroke | 6 | 03-04-2010 08:46 PM |
EC250 to 300 Questions | dave948 | Enduro Engine - 2 stroke | 4 | 01-15-2009 06:12 PM |
Dual sported 06' EC250 questions......... | Harv | General Discussions & Announcements | 5 | 11-05-2008 04:43 AM |
Gas Gas MC 125 questions | MDN91 | Enduro Chassis & Body | 4 | 08-31-2008 05:54 AM |
EC250 '98 gearbox questions | Leon_gasgas | Enduro Engine - 2 stroke | 16 | 09-04-2006 04:50 AM |