|
Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
clutch parts recommendations
My clutch has been dragging a bit for a little bit now and after some investigation ive found that my clutch basket is grooved. Ive read that i can file these grooves down for a temporary fix but id rather just buy a new one and be done with it. And figured i might as well replace the springs and plates as well while in there.
Is the talon clutch basket advertised in the parts section of this site the best option? I have an 03 ec300 and have never had the noise problem with my clutch and hope not to get it with this replacement. As far as plates and springs it seems the most available options for me are moose racing, ebc, pro x, and barnett. Has anyone used any of these with success? Am i better off finding a place to get the stock parts? besides the recent drag i have no complaints about the stock clutch. Any advice would be greatly appreciated. thanks in advance for your help |
#2
|
||||
|
||||
Check the inner basket as well. My '02 200 had enough grooves to drag the clutch. I went through with a dremel carefully which made an improvement, but it wasn't easy & a new one would have been better but my 300 arrived shortly after.
|
#3
|
||||
|
||||
I have the Rekluse basket in my 2010
__________________
Fred Overstreet 2010 EC250 SixDays 2004 GasGas EC300 -Sold to a good home 2006 GasGas EC250-Sold to a good home 2006 GasGas TXT 280 Pro |
#4
|
||||
|
||||
My clutch was grabbing/dragging very badly on my '12 300. Turned out that most of my finger supports were sheered off. In the end, I replaced inner basket with a Rekluse, new plates, and Rekluse outer clutch cover. Now I have zero grab and zero weeping from around clutch cover. Huge improvement over the stock crappy clutch components that came on my new 300.
|
#5
|
|||
|
|||
I'm running a Rekluse inner and outer basket, it works flawlessly.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#6
|
||||
|
||||
Ditto in my 2011
__________________
2011 EC300 Six Days 2010 EC300 Nambotin Replica |
#7
|
|||
|
|||
Buy the rekluse and sell me your 46mm ring gear
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Missing parts at my clutch lever. | motogroove | Enduro Engine - 2 stroke | 5 | 06-13-2012 02:47 PM |
Do GG and YZ clutch parts interchange? | mxfan69 | Enduro Engine - 2 stroke | 2 | 05-25-2012 06:33 PM |
Clutch - new Parts from 2006 EC 250/300 | Klausen | Enduro Engine - 2 stroke | 0 | 05-20-2010 12:55 AM |
clutch parts | jenkitchen1006 | Enduro Engine 4 stroke (including EFI & Exhaust) | 3 | 05-30-2009 06:17 AM |
250/300 clutch parts crossover | Skidad | Enduro Engine - 2 stroke | 5 | 01-09-2008 11:54 AM |