Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Engine - 2 stroke

Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc.


Reply
 
Thread Tools Display Modes
  #1  
Old 04-03-2010, 02:41 PM
Trailrider Trailrider is offline
Senior Member
 
Join Date: Oct 2006
Location: Georgia
Posts: 176
Default Gear shift shaft question (again)

I have all the parts to replace my bent shift shaft. Where does the white plastic donut called the selector axis go? I didn't see one when I removed the bent shaft. Any help greatly appreciated, also any tips on putting the seal back in the right way.
Thanks,
Jim


Reply With Quote


  #2  
Old 04-03-2010, 04:10 PM
gasgasman's Avatar
gasgasman gasgasman is offline
Super Moderator
 
Join Date: Jul 2006
Location: Pearland Texas
Posts: 4,594
Default

It goes behind the shaft seal on the shifter side-basically some sort of oil slinger to keep oil away from the seal.
That's my opinion from a few tear downs I've done in the past.

The slinger is still in your engine case.
Reply With Quote
  #3  
Old 04-03-2010, 05:23 PM
Trailrider Trailrider is offline
Senior Member
 
Join Date: Oct 2006
Location: Georgia
Posts: 176
Default Shift shaft

Will the old one in the case cause any damage? Splitting the cases is not in the plan. I don't have anyone to do it anyway other than send it to GoFasters, and they just rebuilt it a few months ago.
Suggestions?
Jim
Reply With Quote
  #4  
Old 04-03-2010, 06:35 PM
gasgasman's Avatar
gasgasman gasgasman is offline
Super Moderator
 
Join Date: Jul 2006
Location: Pearland Texas
Posts: 4,594
Default

I would pull the seal out and try to insert the rod through the existing axis.
Unless, you can see the axis through the seal opening.
Reply With Quote
  #5  
Old 04-03-2010, 09:03 PM
Trailrider Trailrider is offline
Senior Member
 
Join Date: Oct 2006
Location: Georgia
Posts: 176
Default Shift shaft problem

No sign of the selector axis, she's going back together as is. Just noticed that little piece of plastic I can't use cost me $75. If the gearbox screws up that's the way it goes, it's a 2001 anyway. Any other suggestions welcome other than splitting the cases.
Jim
Reply With Quote
  #6  
Old 04-04-2010, 08:56 AM
gasgasman's Avatar
gasgasman gasgasman is offline
Super Moderator
 
Join Date: Jul 2006
Location: Pearland Texas
Posts: 4,594
Default

You can try laying the bike on it's left side and using a coat hanger to fish around for the axis. You don't want that piece floating around in the transmission.
Reply With Quote
  #7  
Old 04-06-2010, 08:48 AM
Trailrider Trailrider is offline
Senior Member
 
Join Date: Oct 2006
Location: Georgia
Posts: 176
Default Shift shaft problem

After days of confusion the selector axis is just another name for the shift shaft. According to GoFasters the white washer goes on the shift shaft before installing in the case, does this sound correct? I threw away my bent one without looking at it closely. The GasGas fiches are incorrect in several ways and cannot be trusted. There is no internal piece as shown in some years of the parts fiche, that is incorrect. Am I the only one who ever bent a
shift shaft? Is there a correct diagram of the shifter side somewhere? By the time I get the correct parts I'll have a hard time, should have taken pictures.
Any help appreciated,
Trailrider
Reply With Quote
  #8  
Old 04-06-2010, 09:54 AM
stainlesscycle's Avatar
stainlesscycle stainlesscycle is offline
Site Sponsor
 
Join Date: Jun 2009
Location: morgantown, wv
Posts: 1,608
Default

here ya go. there's nothing floating around in there. white bushing keeps selector shaft from moving in and out - without it i would assume the selector(scorpion) could bind
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
shift problems.. stainlesscycle Enduro Engine - 2 stroke 1 05-11-2010 06:25 PM
Shift shaft problems- continued Trailrider Enduro Engine - 2 stroke 10 03-17-2010 12:34 PM
Transnission shift shaft. Trailrider Enduro Engine - 2 stroke 15 02-28-2010 05:10 PM
Gear Selector Shaft Bent? iancp5 Enduro Engine - 2 stroke 11 03-29-2009 04:39 PM
Kickstart shaft question GMP Enduro Engine - 2 stroke 6 02-22-2009 02:55 PM




All times are GMT -5. The time now is 05:06 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org