|
Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Gear lever seal
Can anyone give me instructions on how to replace this seal as its leaking/seeping pretty bad.. Do i need to remove the casing? Or should it just pull out???
Thanks luke |
#2
|
|||
|
|||
Its my ec 250 2000 model
|
#3
|
||||
|
||||
don't need to split cases.
drain oil, remove shift lever, remove water pump cover, remove impeller, remove inner clutch cover, remove cluch and basket. pull shift selector out half way or so. go to other side, remove seal, put new seal in. reverse for re-install. i can't remember for sure if you need to remove impeller to pull the inner clutch cover. but it's an 01, i would most likely replace water pump seal and inspect impeller shaft just as a matter of maintenance.
__________________
07 ec300 was 00 xc200 now a 00 xc300. now parting out. 99 ec300 (now a pile of parts which are for sale) Stainless Cycle - Motorcycle Bolt Kits www.stainlesscycle.com |
#4
|
|||
|
|||
I have never done it, but could you take a set of welding picks and get them between the seal and shifter and pull the seal out. If you bust of the seal that's in it who cares, pull it out and put in a new one.
I don't know if that would work but that's what I would try before I took the motor a part. I could try the 3rd one from the right |
#5
|
|||
|
|||
If you are really good with tools try this: Put a small hole in the seal by drilling or with a thin sharp punch. Run in a sheet metal screw and use the screw to pull out the seal.
__________________
'15 YAMAHA WR250F, '75 YAMAHA TY80 Gone: '00 380 EXC, '03 EC300, '07 YZ250, '07 250 XC-W, '08 YZ450F, '12 CRF250R |
#6
|
||||
|
||||
you can pull the seal without taking the shift shaft out.
reinstalling the seal, and getting it to seat properly would be difficult without removing shift shaft. the frame rail kinda gets in the way, and squaring the seal up is difficult with the shift shaft in the way. it is a 2000 - if it was mine, i would want to tear into it a bit to inspect wear anyways.
__________________
07 ec300 was 00 xc200 now a 00 xc300. now parting out. 99 ec300 (now a pile of parts which are for sale) Stainless Cycle - Motorcycle Bolt Kits www.stainlesscycle.com |
#7
|
|||
|
|||
Thanks again guys very helpful i think i will do it stainlesses way and have a good old look around in there :-) anyone know of where i can get one online im in the uk a link would be handy
|
#8
|
|||
|
|||
The earliest paets list i can find is a 2009 model so can anyone tell me if this is the correct seal me120136048 thanks guys
|
#9
|
|||
|
|||
I would bet that it's always been the same from 2001 up. When I plug that into Gofasters it shows 2006 and a 2010
|
#10
|
||||
|
||||
12x22x7 is the seal. https://www.kingcobradistribution.co...oducts_id=8045
__________________
07 ec300 was 00 xc200 now a 00 xc300. now parting out. 99 ec300 (now a pile of parts which are for sale) Stainless Cycle - Motorcycle Bolt Kits www.stainlesscycle.com Last edited by stainlesscycle; 06-05-2011 at 11:25 AM. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
fse 450 br(e)ake lever $52?!! | T.Low | General Discussions & Announcements | 4 | 09-22-2009 07:25 PM |
Gear Lever crossover? | Leo | Enduro Chassis & Body | 13 | 04-17-2009 04:23 AM |
Crank Seal | kim | Enduro Engine - 2 stroke | 2 | 05-18-2008 09:41 PM |
Gear lever length ???? | pyroman | General Discussions & Announcements | 3 | 05-16-2007 07:59 AM |
00 GasGas EC300 Gear Lever | Gasser370 | Enduro Engine - 2 stroke | 20 | 03-27-2007 10:19 PM |