|
Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Help with Float Level - Low mileage EC250 2013
Hello guys! Like always, sorry for my bad english!
Well, like the title say, need some help with float level. I really think this is the reason about my low mileage. 9,5l only 75km. Here go my specs: Gasgas EC 250 2013 Engine: new, with 19 hours (top end and bearings) Carb specs: 42/175 Air: 1 turn Sea Level: 40 meters Temperature: 25/35C Need help to check where i need to measure. My carb have a PWK on the side. But i can't find a way to see 16mm to this carb. Or the 6mm. Any help would be appreciable. In the pictures, i need to measure from blue to red or blue to yellow line? Thanks! |
#2
|
|||
|
|||
Which PWK is it? Does the top of the carb screw off (AS1) or are there screws attaching the top of the carb to the body (AS2).
The float heights are different for each carb. You should be measuring from the yellow line in your photo (top of the float) to the rim where the float bowl seats (blue line). |
#3
|
|||
|
|||
Hello Jacob. Very good info about ASI or ASII. I will check on my house in a few moments. Thanks in advance my friend!
EDITED: Sorry Jacob, i read wrong. There is screws attaching the top of the carb. Misunderstood something like "typed" in top of the carb. |
#4
|
||||
|
||||
In your pic the yellow line should be parallel to the blue, and then that your measurement. The float itself should appear somewhat level but just off.
http://www.gasgasrider.org/forum/showthread.php?t=11886 Depending on the carb model the distance will vary. See link and other thread you tagged on. |
#5
|
||||
|
||||
Might want to check what needle you have.
My new 2013 came with the "stock" needle and was way too rich. Swapped it out , and all good. Mileage was 25mpg, now 35mpg Will let you know needle type later, as I can't remember! Biff |
#6
|
|||
|
|||
Quote:
Enviado de meu SM-N910C usando Tapatalk |
#7
|
||||
|
||||
Quote:
ktm part no 54731034600 Biff |
#8
|
|||
|
|||
Biff - what jetting are you using ?
|
#9
|
||||
|
||||
Above.. Also OEM for Yamaha YZ series; can look up part numbers. Usually cheaper through KTM.
Will be coupled with a 42 pilot, and 178 main more than likely. Give or take a few sizes. |
#10
|
|||
|
|||
I have the nedw, j&D - red and blue as well.
Last ditch effort - doing to drop the float height - change the needle to #3 Red. Was seeing a ton of smoke last night pilot jet is at 40 Main is at 175 Jakobi - any other ideas ? I also have a #7 slide in it. Should I try the 42 Pilot even though the 40 is smoking a lot? Lenny |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
ASII Float Level With Pix | andoman | Enduro Intake/Carburetion - 2 stroke | 30 | 12-29-2019 12:10 PM |
How to set float level. Revisited. | gasgasman | Enduro Intake/Carburetion - 2 stroke | 48 | 11-10-2018 05:11 AM |
float level 05 ec200 | paulos | Enduro Intake/Carburetion - 2 stroke | 3 | 02-18-2014 05:47 PM |
float level | drn51 | Enduro Intake/Carburetion - 2 stroke | 5 | 01-12-2013 12:15 AM |
Float Level, please explain? | rod | Enduro Intake/Carburetion - 2 stroke | 13 | 02-12-2011 01:03 PM |