Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Intake/Carburetion - 2 stroke

Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc.


Reply
 
Thread Tools Display Modes
  #1  
Old 07-18-2017, 02:05 PM
Davehuge's Avatar
Davehuge Davehuge is offline
Senior Member
 
Join Date: May 2017
Location: English but now based in South of France.
Posts: 470
Default Crank seal sizes? EC300

Does anyone know the exact sizes of the left and right crank seals for the EC300?

I have a good seals and bearings shop nearby who can supply them.

I'm currently having a problem running at WOT (wide open throttle).

The bike runs great at CLOSED to 3/4 throttle, but won't run clean at WOT. After a couple of WOT plug chops the plug looks grey/lean.

I'm a bit concerned as I've tried a 175 and a 180 main jet, just ordered a 185 main jet to try.

I'm starting the suspect lean mixture at WOT might be caused by something other than jetting.

By the way, I'm running in South of France, altitude 500m, temperature 20 to 30?C.

Thanks, Dave.


Reply With Quote


  #2  
Old 07-18-2017, 04:59 PM
Neil E. Neil E. is offline
Senior Member
 
Join Date: Mar 2007
Location: Gormley, Ontario, Canada
Posts: 1,418
Default

Are you certain you have good flow out of your petcock? Tank venting correctly? Carb vents dirty?

Since you tried a larger main jet, it sounds like it might be fuel starvation.
__________________
2011 EC250E
Reply With Quote
  #3  
Old 07-18-2017, 05:38 PM
Davehuge's Avatar
Davehuge Davehuge is offline
Senior Member
 
Join Date: May 2017
Location: English but now based in South of France.
Posts: 470
Default

Hi Neil

Thanks for your reply. Yes I understand what you're staying about fuel starvation.

Just this afternoon I checked the fuel flow out of the tap, also removed the tap and cleaned the filter, all looked good.

I've removed, stripped and cleaned the carb, all seems ok.

Regards, Dave.
Reply With Quote
  #4  
Old 07-18-2017, 07:10 PM
Harry's Avatar
Harry Harry is offline
Senior Member
 
Join Date: Nov 2006
Posts: 301
Default

Hi Dave,

Attached is a list of crank bearings and seals that i used for my 02 EC300.

Hope it helps
Attached Files
File Type: pdf BEARINGS AND SEALS.pdf (17.3 KB, 48 views)
Reply With Quote
  #5  
Old 07-19-2017, 03:22 PM
Davehuge's Avatar
Davehuge Davehuge is offline
Senior Member
 
Join Date: May 2017
Location: English but now based in South of France.
Posts: 470
Default Many thanks Harry...

Hi Harry

That's great information, just what I was looking for.

Many thanks!

All the best, Dave.
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Magura slave cylinder seal sizes? motopsycho87 Enduro Engine - 2 stroke 0 04-08-2017 02:42 AM
oil seal sizes savage sausage Enduro Engine - 2 stroke 5 11-27-2015 06:14 AM
RH crank seal which way round? hillbilly Enduro Engine - 2 stroke 3 03-26-2012 06:19 PM
Seal sizes kendunn Enduro Chassis & Body 0 12-19-2010 09:22 PM
Crank Seal kim Enduro Engine - 2 stroke 2 05-18-2008 09:41 PM




All times are GMT -5. The time now is 06:18 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org