#541
|
|||
|
|||
I bet the guys at PG graphics could make a set up to fit the 10/11? They are very cool guys to work with.
|
#542
|
|||
|
|||
Here's a few updates on mine since I got the top end back together. I have been in love with the Tubliss on the rear so I did one on the front. Also I did a pull type switch on the head light assembly like the KTM's. I kept hitting the bar mounted switch and turning the headlight on and off.
__________________
2013 GasGas XC300E 2005 YZ290 1973 Honda CB175 1997 KX60 1983 Yami Tri-Zinger 1984 Suzuki Alt 50 1969 Trail 90 1971 Trail 90 1972 Trail 90 |
#543
|
||||
|
||||
Quote:
TIA, Jim
__________________
Jim Cook Smackover Racing Team LAGNAF '11 Gas Gas EC250 (primary ride) '06 Gas Gas DE300 2004 Gas Gas TXT300 Pro '94 Husaberg FE350 '86 Yamaha IT200 '86 Honda TRL200 Reflex '04 KTM 525EXC (soon to be dual sported) Several others, including project bikes, Deb's bike, and a fleet of grandkids' bikes Let's go riding! http://www.jebruns.com/Wudi19/wudi19.html http://www.ahrma.org/schedules-results/cross-country/ |
#544
|
|||
|
|||
Serviced the linkage and swingarm bearings, figured since the shock was out getting re-sprung and I never looked at them when I bought the bike I'd have a look. After 25 hrs I wasted my time looking, all the bearings were full of clean grease. What's more
Annoying is not only did they not need doing, two of the bearings spat the needle rollers out and I had to re-pack them, the locating nibs on most of the rollers has broken off. Clearly good quality needle rollers aren't used by the factory on assembly so ill plan on replacing them in the near future when I could be bothered. Anyone have a bearing code for the '14 Linkage by any chance?
__________________
Current: 2014 Gas Gas EC300R _____________________________________________ Previous: 2011 Gas Gas EC300 ELC 2004 KTM 300 EXC |
#545
|
||||
|
||||
Quote:
In the past, before I got All Balls to produce their linkage and swingarm kits in 2002, I often used the rear linkage bearings from Kawasaki, for their '99 KX250. The rollers in those are "caged", as opposed to the "not caged" (which have more rollers but less room for grease). They worked well, and I liked the extra grease. Good Riding! Jim
__________________
Jim Cook Smackover Racing Team LAGNAF '11 Gas Gas EC250 (primary ride) '06 Gas Gas DE300 2004 Gas Gas TXT300 Pro '94 Husaberg FE350 '86 Yamaha IT200 '86 Honda TRL200 Reflex '04 KTM 525EXC (soon to be dual sported) Several others, including project bikes, Deb's bike, and a fleet of grandkids' bikes Let's go riding! http://www.jebruns.com/Wudi19/wudi19.html http://www.ahrma.org/schedules-results/cross-country/ |
#546
|
|||
|
|||
Quote:
__________________
Current: 2014 Gas Gas EC300R _____________________________________________ Previous: 2011 Gas Gas EC300 ELC 2004 KTM 300 EXC |
#547
|
|||
|
|||
Jim, I'm not sure how Gasgas does it. I would have to look at the schematic. I just unplugged the stock switch and plugged some spade connectors into the stock wires then ran it to the new switch. My lights only come on when the bike is running anyway (other than the tail light, but I'll probably change that for the same reasons you stated.)
__________________
2013 GasGas XC300E 2005 YZ290 1973 Honda CB175 1997 KX60 1983 Yami Tri-Zinger 1984 Suzuki Alt 50 1969 Trail 90 1971 Trail 90 1972 Trail 90 |
#548
|
||||
|
||||
My 2011 has the switch cluster (with the "round" light switch on the top), on the left side of the handlebars. The lights stayed on before I disconnected them.
I figure that if I interrupt the headlight's ground wire with a switch, I can shut off all the lights except the tail light (which isn't currently installed). I have the pieces to go street legal, and paid sales tax and have a title, so it shouldn't be too hard in Arkansas. .
__________________
Jim Cook Smackover Racing Team LAGNAF '11 Gas Gas EC250 (primary ride) '06 Gas Gas DE300 2004 Gas Gas TXT300 Pro '94 Husaberg FE350 '86 Yamaha IT200 '86 Honda TRL200 Reflex '04 KTM 525EXC (soon to be dual sported) Several others, including project bikes, Deb's bike, and a fleet of grandkids' bikes Let's go riding! http://www.jebruns.com/Wudi19/wudi19.html http://www.ahrma.org/schedules-results/cross-country/ |
#549
|
||||
|
||||
I rode it, then washed it. Fiddled with the Lectron during the ride, it has a high RPM problem. Need to drop in a new plug and fresh gas to verify it's a carb or electrical issue. Ran well low RPM high and low load, but breaking up around 7400 RPM.
__________________
Phil (New bike pending...) |
#550
|
||||
|
||||
Started it & rode it for the first time since the start of the rebuild in June, stripped to the bare frame and back together again.....started 2nd kick..
__________________
Fred Overstreet 2010 EC250 SixDays 2004 GasGas EC300 -Sold to a good home 2006 GasGas EC250-Sold to a good home 2006 GasGas TXT 280 Pro |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
DNF today | Pepperami | Enduro Chassis & Body | 6 | 09-18-2013 11:59 AM |
Got my first GG today! | RonMexico | General Discussions & Announcements | 6 | 02-19-2011 12:39 PM |
Went Riding Today and..... | coolum74 | Enduro Engine 4 stroke (including EFI & Exhaust) | 2 | 11-30-2008 01:12 PM |
HELP! I tried to use my gasgas as a jet ski today! | sammyj18 | General Discussions & Announcements | 19 | 11-21-2008 08:01 PM |
SHNF From Today | Boomhauer | Pictures & Videos | 13 | 10-30-2007 04:18 PM |