Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Intake/Carburetion - 2 stroke

Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc.


Reply
 
Thread Tools Display Modes
  #1  
Old 10-06-2013, 11:47 AM
Jamie195 Jamie195 is offline
Member
 
Join Date: Sep 2013
Posts: 11
Default 2001 EC 300 Mid Range Problems

Hello,

Recently purchased a GG EC 300. The bike starts easy and idles fine etc. However it has a huge flat spot mid range where it stutters and doesn't feel like it wants to even go through the power band in lower gears. Once past it gets better. It had BR8EG (Very black and wet) so I have changed to BR10EIX as was recommended by the local motocross shop. Carb has been cleaned and has slide #7 and needle on leanest setting. Main Jet is 178 and pilot jet is 38, I live in the UK so elevation is 0-500ft. Reeds look fine and powevalve looks fine. This is my first enduro and 2 stroke so would really appreciate some help and advice, even someone can tell me what size jets to try etc

Thanks very much


Reply With Quote


  #2  
Old 10-07-2013, 12:10 PM
mjtursky mjtursky is offline
Member
 
Join Date: Sep 2013
Location: Fond du Lac, WI
Posts: 27
Default

If I'm not mistaken, a BR10 is a colder plug and would foul easier then the 8. If you are running the factory JN, I would recommend the next leaner OEM JN. In most Keihin PWK carburetors, the straight diameter can influnece up to 1/4 throttle. So very little would change by moving the clip position. That would influence 1/4~3/4 opening.
Reply With Quote
  #3  
Old 10-14-2013, 03:52 PM
Jamie195 Jamie195 is offline
Member
 
Join Date: Sep 2013
Posts: 11
Default

Quote:
Originally Posted by mjtursky View Post
If I'm not mistaken, a BR10 is a colder plug and would foul easier then the 8. If you are running the factory JN, I would recommend the next leaner OEM JN. In most Keihin PWK carburetors, the straight diameter can influnece up to 1/4 throttle. So very little would change by moving the clip position. That would influence 1/4~3/4 opening.
Thanks for the reply... Stuck with the BR8 and I'm just going to try a 172 main jet and leave the pilot jet as a 38. Or do you have any more advice?

Cheers
Reply With Quote
  #4  
Old 10-14-2013, 06:11 PM
Jamie195 Jamie195 is offline
Member
 
Join Date: Sep 2013
Posts: 11
Default

Also does anyone reccomend the RM250 NEDJ needle, I imagine I can try this with my current jetting as its a leaner needle? Although I've only seen people on the forum using this needle on much newer bikes.

(Not familiar with jetting etc)

Cheers
Reply With Quote
  #5  
Old 10-14-2013, 08:32 PM
Jakobi's Avatar
Jakobi Jakobi is offline
Super Moderator
 
Join Date: Oct 2010
Location: Australia
Posts: 7,992
Default

An older model won't like a diameter that lean.
Reply With Quote
  #6  
Old 10-15-2013, 12:04 AM
wrench's Avatar
wrench wrench is offline
Gold Level Site Supporter
 
Join Date: Mar 2010
Location: GA
Posts: 292
Default

Are you getting a lot of smoke from the exhaust when the power drops off?
__________________
2003 GG 300EC/DE [Ohlins]
2001 GG 250XCSOLD
Reply With Quote
  #7  
Old 10-15-2013, 01:48 AM
Jamie195 Jamie195 is offline
Member
 
Join Date: Sep 2013
Posts: 11
Default

Quote:
Originally Posted by Jakobi View Post
An older model won't like a diameter that lean.
Ok is there any you would reccomend? Or would you downjet first
Reply With Quote
  #8  
Old 10-15-2013, 01:49 AM
Jamie195 Jamie195 is offline
Member
 
Join Date: Sep 2013
Posts: 11
Default

Quote:
Originally Posted by wrench View Post
Are you getting a lot of smoke from the exhaust when the power drops off?
Not really, it just stutters but once it's through to the powerband she's fine
Reply With Quote
  #9  
Old 10-15-2013, 05:32 AM
Jakobi's Avatar
Jakobi Jakobi is offline
Super Moderator
 
Join Date: Oct 2010
Location: Australia
Posts: 7,992
Default

What needle is in it? What state is the engine? Reeds? Exhaust packing? Are you certain its a jetting issue? You really need to know the state of the engine is good before you try to jet it up or you'll just go around in circles. The older the bike, the more important.
Reply With Quote
  #10  
Old 10-15-2013, 07:20 AM
Jamie195 Jamie195 is offline
Member
 
Join Date: Sep 2013
Posts: 11
Default

Ill find out what needle at the weekend but I'm certain it's a standard needle, the engine seems fine although I'm no mechanic. Checked the reeds and powervalve all seems fine. I know what you mean about jetting around the problem but I'm not sure what else the problem could be.

Cheers
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
250 tank Range skid jackson General Discussions & Announcements 28 06-12-2012 10:35 PM
range ?? polarity32 General Discussions & Announcements 4 04-29-2012 07:43 PM
fuel range rbm33 General Discussions & Announcements 13 08-16-2011 11:44 PM
2010 EC range bigfoot_zn Pictures & Videos 24 03-18-2011 03:37 PM
no power in mid range !?! help Klausen Enduro Intake/Carburetion - 2 stroke 31 02-28-2011 09:47 PM




All times are GMT -5. The time now is 06:30 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org