Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Intake/Carburetion - 2 stroke

Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc.


Reply
 
Thread Tools Display Modes
  #1  
Old 08-25-2007, 03:19 PM
gasgasman's Avatar
gasgasman gasgasman is offline
Super Moderator
 
Join Date: Jul 2006
Location: Pearland Texas
Posts: 4,594
Default How to set float level. Revisited.

A while back, I posted a link on how to set your float level.

I finally found it after a long search.
Here it is again for those that need to have their's reset..

http://www.dirtridersinternational.c...?TOPIC_ID=2292

Last edited by gasgasman; 08-25-2007 at 09:08 PM.
Reply With Quote
  #2  
Old 02-07-2008, 09:01 PM
gasgasman's Avatar
gasgasman gasgasman is offline
Super Moderator
 
Join Date: Jul 2006
Location: Pearland Texas
Posts: 4,594
Default

For some reason the photos won't come up.
Here they are in the order that they appear in the instructions.


(Float assembly pivot pin not shown.)


(Fuel inlet needle shown with Viton (rubber) tip. The Viton is used to isolate the fuel inlet needle from vibration and to create a better seal against the fuel inlet valve seat.)




Reply With Quote
  #3  
Old 04-24-2008, 11:15 AM
jyellard jyellard is offline
Senior Member
 
Join Date: Nov 2007
Location: Newburgh, IN
Posts: 112
Default

The first link no longer works.

I have checked and adjusted float level on other carbs, so could someone post some basic instructions with dimensions?

Thanks,

Josh
Reply With Quote
  #4  
Old 07-08-2008, 07:58 AM
stay_upright's Avatar
stay_upright stay_upright is offline
Senior Member
 
Join Date: Jan 2008
Location: Coventry UK
Posts: 460
Default

Try this http://www.keihin-us.com/am/_media/pdf/slide_valve.pdf

Float height is mentioned on the right.
__________________
'05 Gas Gas 300
'97 Aprilia Pegaso 650
'99 KTM 200
'95 ish XR630 (died many times in Oz)
Reply With Quote
  #5  
Old 04-11-2009, 11:12 PM
Treesmacker Treesmacker is offline
Member
 
Join Date: Aug 2006
Location: MN
Posts: 82
Default

Quote:
Originally Posted by jyellard View Post
The first link no longer works.

I have checked and adjusted float level on other carbs, so could someone post some basic instructions with dimensions?

Thanks,

Josh
The float Height should be 16mm from the bowl mounting face to the top
of the float as shown in the picture.
Reply With Quote
  #6  
Old 04-28-2010, 11:42 AM
ec300 dave ec300 dave is offline
Member
 
Join Date: Apr 2010
Posts: 6
Default help on float height

Hi can anyone advise me on the correct float height for my year 2000 ec 300.
Reply With Quote
  #7  
Old 04-28-2010, 03:59 PM
stainlesscycle's Avatar
stainlesscycle stainlesscycle is offline
Site Sponsor
 
Join Date: Jun 2009
Location: morgantown, wv
Posts: 1,608
Default

16mm to the best of my knowledge.
__________________
07 ec300
was 00 xc200 now a 00 xc300. now parting out.
99 ec300 (now a pile of parts which are for sale)

Stainless Cycle - Motorcycle Bolt Kits
www.stainlesscycle.com
Reply With Quote
  #8  
Old 05-17-2014, 10:56 AM
liv2day's Avatar
liv2day liv2day is offline
Platinum Level Site Supporter
 
Join Date: Nov 2013
Location: Sherwood, Oregon
Posts: 969
Default

Hey guys, any chance someone has pics showing this? None of the links work and the old pics are no longer there. Need some help as the 250 is pissing fuel out the vent tube when the fuel is on.

Not sure where to measure float height from?
Reply With Quote
  #9  
Old 05-17-2014, 03:29 PM
Jakobi's Avatar
Jakobi Jakobi is offline
Super Moderator
 
Join Date: Oct 2010
Location: Australia
Posts: 7,994
Default

External Link

If the level is right and its still overflowing double check the viton tip on the float needle. Sometimes they perish, othertimes they just have a bit of grit stopping it from sealing.
Reply With Quote
  #10  
Old 05-17-2014, 05:29 PM
Buysomerice's Avatar
Buysomerice Buysomerice is offline
Gold Level Site Supporter
 
Join Date: Jan 2014
Location: St Louis MO
Posts: 185
Default

I just fixed the float level on a kdx last week where the factory specs werent right for that carb because the needle valve seat needed to be altered. Long story short I made a fuel level guage out of tubing and a stopper. The gas goes up the tube to about 2 mm below the mating seam of the carb bowl.
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
EC300 Idle Revisited. Ud_luz Enduro Intake/Carburetion - 2 stroke 35 01-07-2011 07:39 PM
Rear wheel spacers revisited. Ud_luz Enduro Chassis & Body 9 09-13-2010 08:01 PM
Zokes oil level? jostby Enduro Suspension 2 06-20-2009 11:29 AM
Fork oil level ? Brian VT Enduro Suspension 4 03-10-2009 08:57 PM
WP Fork Oil Level MattR Enduro Suspension 11 08-02-2006 10:40 AM




All times are GMT -5. The time now is 03:05 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org