|
Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Gearbox problem after rebuild
Hi guys
Long story short, bought a 2006 EC300 last year that had power like a scooter. But thanks to this forum i changed the needle and some other things, and wow what a bike it turned out to be. Spent more time on the 300 than i did on my R1. Everything went well until the end of the summer when it seized both crankshaft bearings. Now i have rebuild the engine and changed every bearing and seals, but it has even more problem now.. The plan was to start it for the first time in a year tonight. I can't shift. It is in gear but i dont know which, and nothing happens when i pull the lever. I also noticed that the kick starter don't return to the normal position. When i lift the kick lever up i can hear it click. I can kick start the bike but need to manually move up the lever. I checked the service manual and took the time to make everything right. At least i thougt so. Unfurtunately i must have missed something. I have filled the engine with oil, but no oil in the clutch yet. Is it important to fill and bleed the clutch before i could change the gears? Anyone with the same problem? It would be great if it could be solved without splitting the engine again 🙈 Thanks! |
#2
|
|||
|
|||
Problem solved. I had managed to not install the scorpion correctly on the axle. Now it shifts like it's supposed to do 😂
|
#3
|
||||
|
||||
Good to hear, and presumably you have the kick starter spring would up correctly so the lever returns correctly? Just about to put my 07 back together shortly.
__________________
'07 EC300 GG '14 TXT250 GG '? 496 CPI Cheetah RZ/RGV hybrid '22 765 Street Triple RS '21 XTrainer '69 Stinger T125 Suzuki '23 TRS 250RR (it's a Trials thing) |
#4
|
|||
|
|||
Now i have 🙈😂 i was so happy when i found the shifting problem so easy, that i forgot about the kick starter. I put everything together and started the bike, only to hear a rattling noise. Well well, put it on the side and pulled the cover and clutch again. I hope the gasket is good for one more 😂
|
#5
|
||||
|
||||
Gaskets are always good for one more go.
__________________
'07 EC300 GG '14 TXT250 GG '? 496 CPI Cheetah RZ/RGV hybrid '22 765 Street Triple RS '21 XTrainer '69 Stinger T125 Suzuki '23 TRS 250RR (it's a Trials thing) |
#6
|
|||
|
|||
Today we were out on a 70km ride, and wow what a blast it is. Besides the bearings and seals i also changed the piston and clutch. Now i can kick start it when it's in gear. It took a long time to get it running again but it was so worth it 😊
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Ec250 Clutch/gearbox problem | Banwen | Enduro Engine - 2 stroke | 5 | 12-18-2020 12:41 AM |
GG EC 300 '01 - Rebuild // Powervalve problem | Hugo4x4 | Enduro Engine - 2 stroke | 6 | 06-14-2017 07:10 AM |
Just picked up an 06 with a gearbox problem. | shang | General Discussions & Announcements | 12 | 02-16-2016 09:33 AM |
Who can rebuild a FSE 450 starter? Video with problem | olderandyzer | Enduro Engine 4 stroke (including EFI & Exhaust) | 6 | 12-22-2014 04:23 PM |
Front sprocket problem after rebuild .... | Packman | Enduro Engine - 2 stroke | 2 | 03-15-2014 06:18 PM |