|
General Discussions & Announcements General Announcements, General Questions, e.g. What bike do I buy?, etc. |
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
05 Reed Spacer
I have a 2005 EC 250 . I was told that I can put the reed spacer from a 300 to smooth the power out. Has anyone tried this? Does it make much difference?
__________________
2005 GasGas EC 250, 2004 Scorpa SY 250 LR |
#2
|
|||
|
|||
I have it on two 250's, it gives it a little more bottom and takes a little from the top, smoothes the mid some.
__________________
99 EC 300 |
#3
|
||||
|
||||
Yes, and now try the CCK needle.....
|
#4
|
||||
|
||||
What's a CCK needle?
__________________
2005 GasGas EC 250, 2004 Scorpa SY 250 LR |
#5
|
||||
|
||||
What needle are you running? If you don't have the LTR needle then the CCK or LTR needle is you what you should be running. They are single taper and make the power delivery much smoother.
__________________
2004 GasGas DE250 |
#6
|
||||
|
||||
I bought the bike last spring new (left over) from a shop so everything on it is stock. I plan on getting the LTR jet kit and LTR power valve cover along with the spacer in hopes of smoothing the power out for a Senior C rider The bike I rode/raced last year was a 03 KTM 300EXC with lots of low end and it worked really good for me especially in some of the really nasty stuff.
__________________
2005 GasGas EC 250, 2004 Scorpa SY 250 LR |
#7
|
||||
|
||||
Nothing against the LTR jet kit-
THe CCK needle is from www.sudco.com see "Pobit's" excellent post on jetting. I think the CCK is a bit smoother. With the spacer, PV cover, and needle you'll be dialed in. (If it has a flywheel weight or big ignition.) |
#8
|
||||
|
||||
My bike came with a N1EF in it stock and it hit hard. I think you will be very pleased with the LTR needle or CCK needle.
__________________
2004 GasGas DE250 |
#9
|
||||
|
||||
Funny how some try to de-tune the engine and here I am trying to make it a MX bikes almost.
__________________
2002 Gasgas EC250 (gone not forgotten) 2012 Ktm 300xc 2001 Gasgas EC300 Lifes journey is not to arrive safely at the grave in a well preserved body, But rather to skid in sideways totally worn out shouting holy cow what a ride !!!! |
#10
|
||||
|
||||
Mine came with the full street legal kit that has an extra flywheel and stator. I'm not sure if this flywheel would be heavier than the one that's on it now, I haven't taken the cover off the bike yet. Anyone have an idea if it's heavier and would make much difference in power?
__________________
2005 GasGas EC 250, 2004 Scorpa SY 250 LR |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Reed Spacer for EC 250 | GG27 | Enduro Engine - 2 stroke | 4 | 03-28-2009 12:59 AM |
reed spacer | reeve | Enduro Intake/Carburetion - 2 stroke | 5 | 11-28-2008 09:19 AM |
Reed spacer | clerky clerk | Enduro Engine - 2 stroke | 1 | 09-22-2008 03:31 AM |
reed spacer? | moff747 | Enduro Intake/Carburetion - 2 stroke | 2 | 02-26-2008 10:26 PM |