#121
|
||||
|
||||
Hello
How do you reverse polarity on the ebay starter ? |
#122
|
|||
|
|||
Need to rotate the magnet shell or main body by 180 degrees.
|
#123
|
||||
|
||||
Starter
ok took apart - put back together which way should it spin to work ?
|
#124
|
|||
|
|||
There was a good video showing this. I think I linked it earlier in this thread.
|
#125
|
||||
|
||||
starter
found video . problem is i took apart and put back together dont know how its clocked . So should it spin clockwise or counter ?
|
#126
|
|||
|
|||
Finally had a good test of my 24v starter system in a race last weekend. Faultless, started cold in seconds. Started in gear etc. Its worth doing IMO, I just used a Honda Z50 battery which is a AGM not lithium. I will be riveting some proper terminals onto the spade connectors eventually. I might even 3D print a little holder for it instead of the zip ties.
|
#127
|
|||
|
|||
I had a lot of different issues with my e-start. my2018. New bendix cover with bearings help a little and all the bearings must be in very good shape. My problems ended, when added li-ion battery, 48wh. This starter s?stem doesnt work, if battery voltage is below 13v on mine, it doesn't care about starting amps very much. If battery has more than 13v to give, it starts cold, hot, ingear, no problems whatsoever. If voltage is below 13v, u may forget u have e-start, even diesel car battery with 800A starting current straight to starter motor makes only clanking sound, if below 13v.
My sisters boyfriend has same bike, his is acting the same. I interchaged many parts between them (mine had issues, his didnt) and last thing was battery, a fully charged one. One problem still exists, battery charging is too a little bit low on my bike for getting 100% from the battery. I belive the starter engine is wrongly built inside, is there too many or less roundings on the copper wire or are they too thick or thin, i dont know, but it should be possible to rewire them to work higher rpm's on 12 voltage. 24v system was on my mind also, and i'm sure, it helps, but i dont want to carry 2 batterys and make electrical system more complicated, this bike needs simplicity. Rewiring starter motor should do the trick, do we have anybody who is very familiar with electric motors? |
#128
|
|||
|
|||
Hi Doc, I'd heard these were on the way but not seen one yet, any chance you can tell me what he bearing number is, I cant read it from the picture.
Bill |
#129
|
|||
|
|||
Quote:
|
#130
|
|||
|
|||
my cunning plan
just got a well used 018 needs rod crank bearings all the link bearings /swing arm . @@@@ surprise no e start workey my plan new rj cover my one worn out on the small hole . all the parts are ok ish going with them for now think the starter is a ktm ebay one .looking at all the info setting the gears to spin freely is the key . gasket thickness important? ring gear shims ? its got the thinker cable dont no if the cdi has the mod any way of telling thanks for any help
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Wet mod for 2018 starter | GG221 | Enduro Engine - 2 stroke | 20 | 12-05-2022 07:51 PM |
2018 ec300 starting issues! Wtf. | Steveheritage | General Discussions & Announcements | 17 | 09-05-2018 07:52 AM |
05 300ec Turn Signal Issues | natem77 | Enduro Electrical & Wiring | 1 | 04-05-2017 05:14 PM |
Looking for electric starter for 300EC 2012 | oran | "Wanted to Buy" & "Want To Trade" | 0 | 01-09-2016 02:33 AM |
Electric Starter pictures 2011 300EC | gasgasquebec | General Discussions & Announcements | 70 | 12-04-2011 10:01 PM |