#81
|
|||
|
|||
Sorry for the delay, I got busy at work. I have been making some progress.
Do you think the chain guide block was worn out? Another bolt was sheared in half by the chain. Everything else looked good just a little dirty.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#82
|
|||
|
|||
The four rear suspension link spherical bearings were retained by steel circlips. They were very oxidized and difficult to remove. I had to compress the spherical bearing with a socket in a bench vice into one circlip to get enough clearance to remove the the circlip on the other side.
You need these to pry out the circlips. There were eight of these circlips to remove.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#83
|
|||
|
|||
I just received a new oem Suzuki .025 piston and one of my crank bearings arrived as well.
Here is a pic of the rubber mounted triple clamps. The stock bars were original but had been tweaked hard. Anybody got a recommendation on a bar bend? Does anybody know what the renthal bar bend is on the new 2018 XC Gassers?
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar Last edited by Moto7man; 06-05-2018 at 02:52 PM. Reason: add photo |
#84
|
|||
|
|||
Renthal Twinwall 997?
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#85
|
||||
|
||||
That'll buff out.
__________________
'07 EC300 GG '14 TXT250 GG '? 496 CPI Cheetah RZ/RGV hybrid '22 765 Street Triple RS '21 XTrainer '69 Stinger T125 Suzuki '23 TRS 250RR (it's a Trials thing) |
#86
|
|||
|
|||
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#87
|
|||
|
|||
Still Working
I just left a lot of parts at the powdercoaters. I am trying finish up some other things.
I need some help finding the 4 spherical bearings that go in the two rear pushrods. These are 10mm wide, 21 OD and 10 ID. Also, the top steering head bearing has ball bearings with a top and bottom section, and the ID on each section is different(to mate with a bulge in the steering stem). I suppose there is no way to substitute a tapered bearing now.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar Last edited by Moto7man; 06-18-2018 at 02:00 PM. Reason: spelling |
#88
|
|||
|
|||
removing Steering Stem Races
This is the top steering stem, is this a removable race or machined part of the frame. The multi piece bearing above(pictured in previous post) and below, fits this top of the steering stem.
This is what the top bearing looked like before I removed it. The bottom race is normal and I removed it without a problem.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#89
|
|||
|
|||
Progress
I left my parts with a local powdercoater and after two weeks of the continual run around I went and picked up my parts that were sitting in the same pile in the shop floor where I had left them two weeks ago.
I am shipping my parts to my old powdercoater.He does a great job but the shipping is a little expensive. This is what a bike looks like in a box. Engine cases bubble wrapped and boxed up. Hubs, cylinder and other pieces.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#90
|
|||
|
|||
Here is a picture of the oem silencer. It was very oxidized, I cleaned it up a bit with a wire wheel. (Always wear respiratory protection) I am going to have it and the radiators anodized.
The 34 year old radiators don't look too bad.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
94 CR 250 Ground Up Restoration IMS Wide Ratio Transmission Issue | Moto7man | All Other Bikes... | 146 | 01-28-2018 05:57 PM |
1994 CR 250 Restoration featured on Dirt Bike Magazine Webpage | Moto7man | Pictures & Videos | 8 | 10-28-2017 09:12 AM |
Gas Gas Contact Jt 25 95 Restoration And Help | Eyetech | General Discussions & Announcements | 1 | 03-18-2016 03:33 PM |
2001 XC200 Restoration Project | Lincolnlock | Enduro Engine - 2 stroke | 19 | 04-22-2014 03:42 PM |
My Stomping ground | swazi_matt | Ride Reports | 10 | 03-02-2011 09:35 AM |