|
Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
300EC/GP/Jetting
Today I was riding very slow, technical stuff, most of the time in second gear with a quarter to half throttle.
Few days ago I replaced the 172 main jet with a 170, opened the air screw further (now 2,75 turns out). I guess the 42 pilot is too rich. We had about 30? celsius (I think thats 86F) and the bike blubbered, didnt run clean with low throttle openings. Had lots of spooge on the exhaust although I run 80:1... Any hints? |
#2
|
||||
|
||||
For a start put more oil in there man!
Then change the needle. Been covered before more than once and I can't see it being different for the 18.
__________________
'07 EC300 GG '14 TXT250 GG '? 496 CPI Cheetah RZ/RGV hybrid '22 765 Street Triple RS '21 XTrainer '69 Stinger T125 Suzuki '23 TRS 250RR (it's a Trials thing) |
#3
|
||||
|
||||
Copied straight from a response to another thread..
The pilot jet isn't your problem. The stock needle, its short straight section and the rich F diameter of said straight section is the rich condition you are feeling. Odds are that the idle screw is wound in so far that the pilot and airscrew are just about being bypassed. |
#4
|
|||
|
|||
Quote:
Dont worry, I run all my twostrokes (I had 3 300's and one 250) with 80:1 and no problems so far, but I dont want to start an oil thread here Quote:
The problem with the too high idle and hence bypassed idle circuit is quite common but thats ok on my bike. Many thanks for the help, most appreciated. Doc |
#5
|
||||
|
||||
Ktm/Yamaha series needles work a treat. NR8/N2Z/N3C/N3E/etc
So do Suzuki OEM needles NED/NEC series. Usually around a W-H diameter. Sometimes down to a J depending on the conditions. The N1E series that comes OEM in the gassers is the same taper you find in KTM SX models. Have a search. Topics been covered for years! |
#6
|
|||
|
|||
Using 80:1 makes your engine run richer compounding the already poor N1EF needle. Less oil = more gas per unit of fuel, thus richer. We're not talikng huge differences but it all adds up.
__________________
2011 EC250E |
#7
|
|||
|
|||
Quote:
Quote:
Appreciate your help! |
#8
|
|||
|
|||
Try the NEDW to start. NECJ is WAY too lean.
__________________
2018 XC300 |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
need laundry list for 99 300EC and 2000 300EC | steveola | "Wanted to Buy" & "Want To Trade" | 0 | 08-07-2013 12:50 AM |
2011 300EC Jetting | 400exc | Enduro Intake/Carburetion - 2 stroke | 7 | 04-04-2013 05:36 PM |
Jetting help 2011 six days 300ec | Colemanian | Enduro Intake/Carburetion - 2 stroke | 9 | 11-14-2012 09:52 PM |
Need help- 300ec not right! | ucrtwf | Enduro Intake/Carburetion - 2 stroke | 8 | 03-26-2012 03:08 PM |
'02 300ec | Bultaco206 | General Discussions & Announcements | 2 | 01-23-2007 06:40 PM |