|
Enduro Chassis & Body Enduro Frame, Plastic, Brakes, Bars, Controls, wheels, tires, sprockets & gearing. |
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
2013 GasGas Plastics
Just thought it is worth noting.
I used the GoFasters number plate mounting kit to mount a 2009 CRF 450 number plate to my 2013 GasGas 300. To be fair I only used the upper bracket to assist in mounting. I used the headlight mount pegs on the stock front fender. I had to drill alignment holes to allow the crf number plate to slip over the pegs and stay put. It seems there is a lot of wiring behind the plate so I mainly fitted the plate to allow for the wiring to not "squeek" I will play more later. Ridepg.com graphics are very, very nice. So, I wanted black rear number plates. So first thought, buy 2014 plates. Nope, does not work, you need a 2014 airbox to allow for this not a big deal but I will have to buy some 13 number plates instead!
__________________
2013 GasGas 300 2004 GasGas 200 2011 GasGas 300 Ortonville Minnesota |
#2
|
|||
|
|||
So the black side plates from a 14' do not fit on 12' or 13? If thus is the case I hope they didnt get included in my plastics order?
|
#3
|
||||
|
||||
They did not.
__________________
Steven Beane #275 PlusOnePerformance - Superior Service the World Over - Dearborn MI AMA District 14 (Michigan) Officer afterhourscycle.com Michigan's Beta and TM Race Headquarters |
#4
|
|||
|
|||
Its a bummer they don't fit, I was really hoping for black plastics.
|
#5
|
||||
|
||||
Why do you say the 14 side panels won't fit on 12-13? I installed a 14 plastic kit on my 12 no problem.
__________________
15 GASGAS EC 250 19 Sherco SE 125R |
#6
|
||||
|
||||
The alignment holes/tabs are not the same. I would imagine the fenders/shrouds may be the same, but the rear number plates are far from the same. I think if you swapped the airbox, that may allow for the 14 number plates. Maybe if you have the aluminum subframe? I may have to go do some detective work to see the differences.
__________________
2013 GasGas 300 2004 GasGas 200 2011 GasGas 300 Ortonville Minnesota |
#7
|
||||
|
||||
Well I installed the alum subframe at the same time. I guess the subframe cover slots are different? I'll check when I get a chance.
__________________
15 GASGAS EC 250 19 Sherco SE 125R |
#8
|
|||
|
|||
Ok, you have the plastic subframe on your 13' and the side panels don't fit? But they will fit the aluminum subframe? If this is the case I have the aluminum subframe. Is there a definite answer to this?
|
#9
|
||||
|
||||
I'm guessing it may be a 14 subframe. Do you have 2 tab holes or just one tab hole and one bolt hole? The 14 plates have one tab and one hole on the left side of the bike. 13 plates have two tab holes.
__________________
2013 GasGas 300 2004 GasGas 200 2011 GasGas 300 Ortonville Minnesota |
#10
|
||||
|
||||
If you have the alum subframe and single tab number plates now, the 14 number plates will fit. Just lose the left hand alum spacer from the mounting bolt.
__________________
15 GASGAS EC 250 19 Sherco SE 125R |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
when did gasgas change plastics | whodat | General Discussions & Announcements | 2 | 06-24-2009 06:56 AM |
GasGas plastics from Cemoto | MattR | Enduro Product Announcements | 5 | 06-19-2008 07:20 PM |