![]() |
|
Enduro Product Reviews Feedback & Comments on Products Tested |
![]() |
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
![]()
Here is my short review on the smartcarb fitted to my 2012 300 race
I picked the carb up on thursday from ups and had a quick look at it on thursday night and took the following pics ![]() ![]() ![]() ![]() Its well boxed and presented , and a thing of billet beauty |
#2
|
||||
|
||||
![]()
Now for a look inside
![]() ![]() ![]() ![]() If you look on the top plate you can see the underside of the adjuster and how it goes into the slot on the top of the slide , nifty idea |
#3
|
||||
|
||||
![]()
Now the bowl
![]() ![]() And finally the shape of the bore , sort of egg shape ![]() |
#4
|
||||
|
||||
![]()
Ill post a few pics up on the bike later when iv cleaned the bike.
On the 12 bike the cable wont fit into the adjuster on the top of the carb so i replaced it with the one in my venhill kit but then the standard cable was too short so i made up the venhill kit , i made a decent job of that but had to enlarge the hole of the throttle adjuster as the venhill ferule was too big , i will get a couple more kits and perfect it a bit more , but it worked perfectly all weekend as is . Fitting the carb was simple enough , i removed all bolts from the subframe wiggled the carb in from the left side and fitted to the inlet boot , i then put a small ammount o heat into the airbox boot and fitted that and bolted up the subframe. I fitted the slide and fuel tank and tried to start her but no go,When i put the bowl back on the carb the floats did not seat correctly and flooded my motor in a very short time , so it was off with the sprocket guard and tilt the carb over and try to reseat the floats , same again flooded bike . Last go , i got a small zip tie and held the tang in the closed position while offering the bowl up and it finally worked , thats the price you pay for playing i guess , my fault totally. After several kicks the bike fired up and after clearing the leftover gas had the best idle she has seen so far ( as others have said ) , i left the bike to idle for over 10 mins and she sat idling perfect at the same revs all the time , i gave her a blip on the throttle expecting her to be chocked up but not at all , instant response. The following morning it was frozen outside and i went into the garage with the intention of trying to start her with no choke as a few have said they required no choke , i couldnt believe it the bike started first kick . Out on the trails on sunday it very wet so not the best test , but the bike does run better than before , ou can ride a gear higher and there does seem to be more available power , there was a bit of a rich point at about 1/3 throttle , i did try to adjust the carb on the trail but i could not get it to work and im going to look at that later . The only problem i had is when i gave another guy a go and he fell off , the bike flooded and took loads of kicking to restart , same when i fell off a couple of times , unless you are very quick to pick the bike up when falling off expect to kicking a lot , looks like i need some of those one way valves that were mentioned in the other thread. After we had been riding for a easy couple of hours we stopped to fuel up , my bike took 4.45 ltrs and my mates standard 12 300 took 4ltrs , but bear in mind i run this carb exactly as it came out of the box . So now im looking foreward to my next session so i can tinker a bit more and perfect the setup. Chris |
#5
|
||||
|
||||
![]()
Nice report Diggs.
Cheers Mark
__________________
Xr 250 ( first bike) 98 Rmx 2007 Gas gas 300(swapped for trials bike) 2008 280 Raga replica 2012 Gas gas ec 300 E ![]() |
#6
|
||||
|
||||
![]()
Hello Diggs 345, Did you abandon the cable choke ? I'm in the process of speaking w/ Aaron @APT for a solution. I would prefer to keep the cable.
I'm waiting for my cylinder head to return. Then I will have some more input. |
#7
|
||||
|
||||
![]()
Nice report man thanks for the info, I suspected that without the check valves. I wanted and was going to get the billet version but that one thing alone was why I'm waiting for the cast one.again Thanks for the review
__________________
trevor |
#8
|
||||
|
||||
![]()
Thanks for the replys ,
John , i took the choke cable off from day one of getting the bike , but i think you will find you dont need the choke , it was freezing outside and mine started up first kick ![]() It seems to my eyes that the slide spring is a little too long and thats whats stopping the plunger/adjuster making contact with the screw on the top of the slide , ill have another look though before i trim it ![]() |
#9
|
||||
|
||||
![]()
Great report. Please let us know when you get it sorted.
Sounds like with the richness, you'll adjust it a click leaner? Like Nambo, I was actually squeezing the trigger aiming at the billet unit. I stood down with concerns about flooding. I have logged hours of kicking on an old XR 600 in the late 80's. Each get-off was more tiring than the entire ride or race. No desire to re-visit that pain...
__________________
Newest Spanish Girlfriend: 2011 300 Six Days My Daughter is a U.S. Marine |
#10
|
||||
|
||||
![]()
There was a guy out with us on Sunday with an xr650 , he spent a lot of his time pushing out of bogs and kicking it, I did feel a little sorry for him but glad I have the bike I have.
I also got the chance to ride a exc 450, it felt so crude and every time you shut the throttle it stalled , good job it had es |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
brushy ride review, bike review, Add on parts review | Mazikeen | SouthEast United States | 6 | 09-04-2012 05:34 PM |
2012 300 Review......WOW!! | Jeff Melik | General Discussions & Announcements | 15 | 05-09-2012 09:10 AM |
Could someone smart tell me whats going on? | dank | Enduro Intake/Carburetion - 2 stroke | 10 | 04-16-2010 07:46 PM |
2009 Review | 2 strokes 4 life | General Discussions & Announcements | 2 | 11-26-2008 10:30 PM |
Review of RB Design | LAWMAN | Enduro Product Reviews | 6 | 07-13-2007 03:04 PM |