|
Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc. |
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
Pipe surface rust removal?
Since I have my bike semi-pulled apart for the head-mod, I want to get the surface rust removed from my pipe
Any good suggestions on how to do so? And when I have it cleaned up, what's the best method to keep it off (aside from drying after a wash - which I always do)? |
#2
|
|||
|
|||
http://www.nevrdull.com/
If it's just rust staining, check out the link. Nothing will work if the surface is badly pitted.
__________________
2011 EC250E |
#3
|
||||
|
||||
I use the same stuff. Works great just make sure you remove all of it once it dries.
__________________
'12 XC 200 TTX Sold '15 XC 250E Sale pending Last edited by john r b; 03-31-2014 at 05:38 PM. Reason: spellin |
#4
|
||||
|
||||
Thanks guys, I'll pick up a can and go to work on the pipe this weekend
|
#5
|
|||
|
|||
WD40 & green Scotchbrite worked great on my Muzzy for the ZRX, was planning on giving that a go on my FMF in the next few days. Hit it with a little metal polish after that and it will glow.
__________________
-Keith '08 EC250 and some other bikes. |
#6
|
||||
|
||||
x2 its what I had in the shed and did a good job of it
__________________
06 EC250 |
#7
|
||||
|
||||
x3 That works great for me also on my ZRX with the stainless Tiforce header. I follow it up with brake clean on a rag to wipe it clean.
__________________
Noah 2000 EC250 with 2011 transformation kit, KYB SSS forks, MN street title 16' Ski-Doo XS Renegade X 1200 4T 16' Specialized Fatboy trail 02' ZRX 1200r R.I.P. 72' Olds 500ci, Batten Heads, Street/Drag car, former CarCraft magazine centerfold (has-been) 15' TW200 |
#8
|
|||
|
|||
sos pad works great for runst
|
#9
|
||||
|
||||
Another option is #0000 steel wool and your favorite metal polish.
__________________
Noah 2000 EC250 with 2011 transformation kit, KYB SSS forks, MN street title 16' Ski-Doo XS Renegade X 1200 4T 16' Specialized Fatboy trail 02' ZRX 1200r R.I.P. 72' Olds 500ci, Batten Heads, Street/Drag car, former CarCraft magazine centerfold (has-been) 15' TW200 |
#10
|
||||
|
||||
Sweet, thanks for the additional input. I'm going to do the WD40/Scotchbrite method first, then I figure I'll follow that up with the Nevrdull polish - sounds like a great combination.
I'll have to take some before and after pics |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
2012 Air Box Filter Mating Surface | rickster2 | Enduro Chassis & Body | 6 | 11-08-2012 06:53 PM |
exhaust pipe removal | BryanMcc | Enduro Engine - 2 stroke | 7 | 06-15-2012 08:56 AM |
Pipe Dent Removal | savage sausage | United Kingdom | 22 | 02-21-2012 07:51 PM |
Rust on my shock | Gonzo | Enduro Suspension | 3 | 08-30-2006 01:29 AM |