parting out an 03 ec250

[SideshowBob]

Originally Posted by mxdj2003

i will have a set of wheels for sale i had a buddy powder coat them black and there not back yet

let me know when you measure the triple clamps. I am dying to see if they will work.

For the subframe and all the parts- what is the main advantage of switching over to 2007 parts? I know the earlier subframes are weak, what else gets replaced? I am trying to decide if it's worth the extra money ($200+) over buying a rear subframe to replace my bent one from GoFasters.

Also wondering if my Guts seat will fit on the new rear subframe.

Also, do you have the rear brake assembly with Master Cylinder?

[mxdj2003]

sideshow, the bottom clamp ID 2.240 and the top is 2.120 . i do have the rear brake set up as well ill take 50.00 for it and its got new pads

[gasser]

Slideshowbob in case you're wondering the WP FORKS do fit the newer bikes with Zooks. I put 01 WP tubes and front wheel on my 07 bike when I sent the Zooks off for revalving. They fit right in the 07 triple clamps.

[svt2224]

Mxdj2003,
Did you get my PM?

[SideshowBob]

Originally Posted by mxdj2003

all these parts will bolt right up, the rear fender has no tailight

Originally Posted by gasser

Slideshowbob in case you're wondering the WP FORKS do fit the newer bikes with Zooks. I put 01 WP tubes and front wheel on my 07 bike when I sent the Zooks off for revalving. They fit right in the 07 triple clamps.

I have a 2003 MC250 with the Ohlins suspension option (I was told there was such at thing). It has upside down Ohlins forks.

Originally Posted by mxdj2003

sideshow, the bottom clamp ID 2.240 and the top is 2.120 . i do have the rear brake set up as well ill take 50.00 for it and its got new pads

poop, I think it sounds too small but I am not sure. Can you do mm's? I am gonna call Mark at Go Fasters tomorrow and see if he knows. The current Triple Clamp top does have a "GG" stamped/casted on it, so I am guessing that was factory and I should be OK with this used one to replace my slightly F'ed up one.

With the brake setup, I am mostly concerned with the pedal/lever and master cylinder, were you including all that?

[mxdj2003]

my clamps do have GG stamed on the upper clamp i'm sure they will work, buy them and if they dont work i'll give you a refund , the rear brake set up does come with a master cyliner and brake pedal, but the pedal is one i modified it uses 2 bearings where it mounts up eliminating any slop its a cool part it does have a braided line as well

[SideshowBob]

Originally Posted by mxdj2003

my clamps do have GG stamed on the upper clamp i'm sure they will work, buy them and if they dont work i'll give you a refund , the rear brake set up does come with a master cyliner and brake pedal, but the pedal is one i modified it uses 2 bearings where it mounts up eliminating any slop its a cool part it does have a braided line as well

Awesome, you'll have a PM soon.

The triple clamps won't work

[forgiven]

Do you have a clutch cover available?

[les]

Is a seat available?

[jprh]

Originally Posted by mxdj2003

you get the subframe, seat ,air box assembly, rear fender and airbox sides, all the parts are brand new , ill measure those clamps tonite and PM you

ive been away 4 work for 4 days i will buy the lot can u re quote me plus the postage to australia as soon as i get a reply im gettin a mate to teach me how to pay pal to your [amy] address thanks dave. jamie ph 0401230418