|
Enduro Suspension Tuning & maintenance of Enduro forks, shocks, etc |
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
Need to find Inner cartridge bushings-48mm marzocchi’s
Does anyone have the part number or know where to get inner cartridge fork bushings for the 48mm dual chamber marzocchi’s
See attached pic. I’ve ordered two different sizes from racetech with no luck. The last set I got look correct but measure 36.15mm when assembled and require a lot of force to assemble and do not slide nicely when assembled. Sent from my iPhone using Tapatalk |
#2
|
|||
|
|||
I've generally found that most bushings require filing on the open ends in order to fit correctly
__________________
2006 EC300 Enduro - Ignitech CDI - 38/NECW#2/165 FMF gnarly, FMF shorty, .50 front 5.7 rear 2016 RM-Z450 |
#3
|
||||
|
||||
Perhaps you could make the new bush thinner by removing some material fom the inside?
Did you ask your favourite GG dealer? I have had success with sourcing Marzocchi parts from my importer, but that was a part that has a part number in the parts catalog. I see that this bush is in the drawing, but without a part number in my 2015 parts catalog.
__________________
Anders "So you know, that you're over the hill when your mind makes a promise that your body can't fill" (Little Feat: Old Folks Boogie) 2015 EC200 Racing: TE bars, Rekluse Core Exp 3.0, 38mm Lectron & Ohlins S3 steering damper 2006 EC200: 2011 plastics, Rekluse Z-Start, revalved KYB forks & Scotts steering damper 1998 Bimota Supermono 1986 Duc Mille S2 1975 Guzzi sidecar hack 1961 Morini Corsaro 125 etc |
#4
|
|||
|
|||
Matto Cycle can hook you up. He will be doing mine next week and has replaced them in the past.
|
#5
|
|||
|
|||
think there the same as 48 mm kyb.the seals are.
skf do bush kits |
#6
|
|||
|
|||
bit like piston rings you need a gap . i do vintage suspension often have to shim the bushes
|
#7
|
|||
|
|||
I have asked my local dealer but have not had much luck. He said he would look into it but have not heard anything back.
How would you recommend removing material from the inside? There is a small end gap already. I’d like to make these work as I already have $$ invested and can’t return them. If all else fails I’ll check with Matto. Thanks guys. Sent from my iPhone using Tapatalk |
#8
|
|||
|
|||
Fork Bushes
Innteck does them. The link can help as a guide.
Should be able to find Innteck as they are US made. http://www.jwtimports.com.au/downloa...ents-Guide.pdf |
#9
|
||||
|
||||
Quote:
make a holder for the bushing. (a cylinder of slightly lower ID than the bush OD), puth the holder in the lathe and the bushing in the holder. As you want to remove only a slight amount, use e.g. 320 paper and lightly remove some material. Place the bushing on the piston, measure O/D. Repeat as needed. I haven't tried to do it, but that would be my approach.
__________________
Anders "So you know, that you're over the hill when your mind makes a promise that your body can't fill" (Little Feat: Old Folks Boogie) 2015 EC200 Racing: TE bars, Rekluse Core Exp 3.0, 38mm Lectron & Ohlins S3 steering damper 2006 EC200: 2011 plastics, Rekluse Z-Start, revalved KYB forks & Scotts steering damper 1998 Bimota Supermono 1986 Duc Mille S2 1975 Guzzi sidecar hack 1961 Morini Corsaro 125 etc |
#10
|
|||
|
|||
Need to find Inner cartridge bushings-48mm marzocchi’s
I need the bushings for the inner cartridge not the normal fork tube. The previous owner broke the fork bleeder and continued to ride which allowed dirt and moisture into the inner cartridge.
Sent from my iPhone using Tapatalk Last edited by rvangeel; 04-28-2018 at 01:26 PM. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
PFP adjuster on 48mm Marzocchi’s | rvangeel | Enduro Suspension | 2 | 03-18-2018 03:26 AM |
Marzocchi 48 Cartridge Problem | fixmare | Enduro Suspension | 30 | 09-11-2017 05:38 AM |
Fork Oil Volume for 2013 Shiver 48mm Closed Cartridge | scov | Enduro Suspension | 3 | 04-21-2013 02:04 AM |
Sachs 48mm Bushings | Jakobi | Enduro Suspension | 9 | 06-19-2012 07:18 PM |