|
Enduro Electrical & Wiring Lighting, Ignition, Wiring, Plugs, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
E-Starter Kit EE855002513
Hi,
while I'm waiting for my E-Starter Kit (EE855002513), which is on its way from the US, I have a question: The E-Starter Kit (EE855002513) is for the Gas Gas EC300 2012-2013. Their CDI is positioned differently than it is in my EC300 2011. I don't know if I can reposition my CDI for the supplied harness to work or if I need the Wire harness P/N EE101002510. Anyone knows or can find out what I have to do or what else do I need to install the 12-13 Kit in my 2011? Thanks and regards, Gerardo Temuco, Chile |
#2
|
||||
|
||||
I repositioned my cdi to the 2012 location on my 2010 ,but it is tight. Some fabrication is needed.
__________________
Claude 2019 XC300 2010 Nambotin 300 sold '07 EC300 sold '06 EC300 sold '78 Suzuki RM250C2 '75 Yamaha YZ250B sold |
#3
|
|||
|
|||
Hi Claude, tnx for your reply. Where is the 2012 CDI positioned, do you have any picture or is it shown up in a 12 Manual? I also figure out to enlarge each single wire that goes to the CDI, no problem to me to do that, but perhaps I need to remove my CDI to make place for the battery. What is your suggestion please? Regards from Chile
|
#4
|
||||
|
||||
The CDI is on the front frame downtube in front of the fuel tank. Yes you need the room in the air box for the starter relay.
__________________
Claude 2019 XC300 2010 Nambotin 300 sold '07 EC300 sold '06 EC300 sold '78 Suzuki RM250C2 '75 Yamaha YZ250B sold |
#5
|
|||
|
|||
Hi Claude, tnx for the info. Is your starter running fine? I've read about plenty of issues with the bendix and/or the adjustment (clearance) between it and the FW gear. Do you have any installation suggestions or are there any somewhere? Have you done the CH80 Honda bendix mod? Is it worth to do it? How did you install the battery? I have an Alu Sub-Frame (my 2011 is the Replica Nombotin) but without batt support. (The Nambotins are top bikes). Thanks
|
#6
|
||||
|
||||
I also have a Nambotin. I did use the scooter bendix. I tried a regular battery but it didn't have enough power so I bought a Shorai and it works great! I bought a new subframe with the battery box for cheap so that's where it sits. If your handy you could fabricate an battery holder to you existing sub frame.
__________________
Claude 2019 XC300 2010 Nambotin 300 sold '07 EC300 sold '06 EC300 sold '78 Suzuki RM250C2 '75 Yamaha YZ250B sold |
#7
|
||||
|
||||
What? You found an electric start conversion in the U.S.? May I ask where from?
__________________
WildAzzRacing YouTube channel Trail Riders of Southern AZ club AZ State Parks OHV Ambassador '11 EC250R '98 KDX220 |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
e-starter kit! | Frie82 | "Wanted to Buy" & "Want To Trade" | 0 | 08-29-2017 02:03 PM |
15 starter set-up | pigpen966 | Enduro Electrical & Wiring | 5 | 10-02-2016 05:48 PM |
Can I add a starter? | Jeffm | Enduro Electrical & Wiring | 17 | 11-09-2013 07:23 PM |
starter jet....where and how? | mp5 | Enduro Intake/Carburetion - 2 stroke | 1 | 05-01-2013 09:13 AM |
starter on 450 ec | jenkitchen1006 | Enduro Engine 4 stroke (including EFI & Exhaust) | 3 | 05-21-2009 06:38 AM |