#41
|
||||
|
||||
Quote:
Do you know where I can get one ? I'm not sure if I'll need it but I'm trying to get info on various parts I might need before I get started. Vinny |
#42
|
||||
|
||||
Cdi ?
Would a '02 CDI (Magneti Mirelli IAV 15P) work on my bike ('05 FSE 450). Looked it up and its the same number from '08 on down
|
#43
|
||||
|
||||
Quote:
I have checked all fuses and wiring connectors. Checked for spark and there isn't any. Fuel pump is working, as are all lights. Cant find any kill switch wire (turns off w/ key). I have attempted most, if not all your suggestions. I guess it comes down to electrical parts. I have the CDI out. IAW15P.LO It has GAS GAS 400 FSE and the # 2-3489S5D Not sure if this came w/ it originally or they just used that kind for all ( my bike is a 450 FSE) I found a CDI in Germany ebay. Its from an '02. IAW15P.EO Do you think it could work ? Its a $ 200 gamble. Otherwise a new one is $ 600. What is the silver box that is attached to the right side of the frame at the front, behind the radiater ? Regulator ? Thnanks. Vinny |
#44
|
||||
|
||||
I think trying a "CDI" off a different bike is ok for a test but I wouldn't run with the wrong one. It's not just a CDI it controls the injection i.e. mixture so unless you are able to check the mapping and adjust I'd be very careful. If you get one from the identical spec engine it should be ok though. The engines changed a few times. I "think" the 2006 until 2009 is the same but 2005 was different - it's a different bore for starters, not sure what else was changed. Check the cam and valve part no.s and also the fuel pump, throttle body and injector. If it was only a small bore increase in 2006 you "may" be ok.
|
#45
|
||||
|
||||
Have you verified that your pickup coil is ok? By measuring or doing the slow kick method? Spec was on one of the pdf's I mailed you, as turn/rpm sensor.
|
#46
|
||||
|
||||
I think you will still need the diagnostic software/lead if you intend to keep the bike after you fixed it. See if you can find a used one or borrow one from someone on here maybe? Swapping ECUs (not CDI) may or may not fix the problem. It may also wreck a perfectly good ECU in the process if there is something else bad which caused the failure in the first place. The maps will most likely be different year on year and maybe some of the connections are also different. If you check the ECU part numbers in the parts lists online it should give you steer as to which are interchangeable. Blanket bombing is no substitute for diagnosis IMHO.
And yes the silver (aluminium) box on the frame rail behind the LH radiator is the shunt regulator for the alternator.
__________________
06 Gas Gas FSE 450 USA 07 Gas Gas FSR 450 UK with motard and dirt wheels |
#47
|
||||
|
||||
Quote:
Thanks . V. |
#48
|
||||
|
||||
If I remember this correctly, slip back the rubber cover, and the connector is hiding underneath.
|
#49
|
||||
|
||||
Will someone in US with a '03-05 450 be willing to receive my ECU and coil/spark plug wire and try it on their bike to see if they still work ? It would mean taking the gas tank off and plunging it in, then trying to start the bike . I know its a lot to ask. It would save me buying parts to see witch one is at fault. I could even pay an hrs wage to that individual. If you are willing please PM me.
Thanks. Vinny . |
#50
|
||||
|
||||
I did. My kick started seems to have stripped .
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
2005 FSE450 wont start | itsagas | Enduro Engine 4 stroke (including EFI & Exhaust) | 5 | 05-16-2010 08:38 AM |
02 EC 300 wont start | GENO 300 | Enduro Engine - 2 stroke | 0 | 09-21-2009 10:02 PM |
EC200 wont start | Skele | Enduro Engine - 2 stroke | 25 | 09-06-2009 10:34 AM |
wont start | clerky clerk | Enduro Engine - 2 stroke | 8 | 11-01-2008 01:18 PM |
2000 Xc 250 wont start In mesa arizona | justinmanus | Enduro Engine - 2 stroke | 9 | 12-25-2006 04:46 AM |