|
Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Newbie bought 2004 EC250 - need help with parts
Hey guys, I am a newbie to GG (I am a converted KTM rider).
I need help in identifying basic parts like brake and clutch levers, throttle cable, and brake pad replacements. Any specific help is appreciated. I don't want to be let down with this GG purchase, but finding parts has been time-consuming to say the least. Thanks, Brian |
#2
|
|||
|
|||
For example, I saw a brake lever listed on gofasters.com for $64.....Ouch! there has to be other options.
|
#3
|
||||
|
||||
moose racing has both the standard length clutch and brake lever. look under the oem replacement lever section. the throttle cable, you are best off calling up gofasters and getting their 1.5 inch extended cable made by motion pro, it provides a little wiggle room and will run around 35 bucks if i remember right. other bikes like hondas and ktm use the same carb and basically the same cable, but there is a fixture at the carb end of the cable which makes a bend to fit around the gas tank, so the other brands cable will not work. brake pads off a honda cr, 87-01 (from the cross over list) GoFasters will have all of the parts you need. the link to their website is under the parts tab at ggor.us
i hope your gasgas will not let you down. yes, sometimes parts can be hard to find, but they are a fantastic bike. good luck!
__________________
03 ec250 hyde skidplate, cycra handguads, protaper contours "what? it seemed like a good idea at the time!" |
#4
|
||||
|
||||
by the way, it is often easier to call gofasters, rather than use the website. the website is functional, but it has its quirks. i have called multiple times and they are knowledgeable and fast.
__________________
03 ec250 hyde skidplate, cycra handguads, protaper contours "what? it seemed like a good idea at the time!" |
#5
|
|||
|
|||
Yeah, first thing to do is go to the parts crossover page, http://www.gasgasrider.org/html/parts_crossover.html
There are lots of other things that will work also, just do a search. Your best bet is the classifieds on here, lots of stuff to be had very reasonable (usually). One great thing about GG parts is a lot of times they will list the size on gofasters so you can find a universal replacement for things like bearings.
__________________
2006 EC300, 2000 XR650R, 2003 EC250, 2001 EC200 (OK, the last two are really my sons). |
#6
|
|||
|
|||
Halls Cycle is also a good place for parts. check them out http://www.halls-cycles.com/index.html
|
#7
|
|||
|
|||
Quote:
|
#8
|
|||
|
|||
They'll work on your '04.
__________________
jeff '00 XC250 (mine) LTS front and rear suspension, power valve cover, carb jet kit and rear chain glide, RB Designs head mod, BRP tall triple clamp, backyard foot-peg lowering conversion. '04 EC250 (the kids) (he can do his own mods haha!) |
#9
|
|||
|
|||
The pads will work for any GG with Nissin brakes. They are from a 87-01 CR250 and also the same ones on my XR650R and the fronts are the same as my sons CRF230, so I am sure there are many more they fit.
__________________
2006 EC300, 2000 XR650R, 2003 EC250, 2001 EC200 (OK, the last two are really my sons). |
#10
|
||||
|
||||
Quote:
AJP-compatible clutch levers are a little tougher to find in the typical channels. Try http://www.tryalsshop.com or http://www.lewisportusa.com/ for a good selection of AJP clutch levers.
__________________
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Forum newbie (ec250) | gregtenerife | General Discussions & Announcements | 3 | 03-12-2010 08:19 AM |
Bought my first Gas Gas 05 EC250! | motobilly | General Discussions & Announcements | 4 | 08-11-2008 08:49 PM |
I bought a Gasser ('05 EC250) | AZRickD | General Discussions & Announcements | 33 | 04-03-2008 08:28 PM |
Gasser Newbie- just bought FSE400EC!!! Any advice? | pbgunrunner | General Discussions & Announcements | 3 | 05-11-2007 07:40 AM |