Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Engine - 2 stroke

Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc.

Thread Tools Display Modes
Old 07-13-2015, 06:56 AM
barossi73's Avatar
barossi73 barossi73 is offline
Gold Level Site Supporter
Join Date: Jan 2014
Posts: 551
Default map switch

A couple of questions/observations arose from my most recent ride.13 ec200
bike is jetted for 10-25deg c, 40p,175m,nozh#2
Recently had a little snow which mostly melted but hard frosts froze what remained on the cold shady backsides(last few days -5 to 5deg),which made for treacherous conditions,hard fast dry on the frontside,half melt or ice on the darkside.
Armed with a 30hr recut rear pirelli with no edge grip i crossed over the backside and began to traverse a steep frosty slope...
the rear wheel got to the bottom first...
#1-its well worth cutting the side face of knobbly as well as just the leading edges!(the edge that bites when rear goes sideways)
no harm done,straighten brake,quick lookover...
#2-the gap between my expansion chamber and rightside rad hose is less than 1mm.no visible heat damage to hose.
Q.is this an issue with heat on hose?and how much clearance on others bikes?
ride on...tear up some hillclimbs and decide the bike is definitely a little lean for 4deg.fiddle the screws and can make no better...i dont usually bother with the map switch but decide to try it...
usually in rain mode throttling is a little fluffy(10-25),but today at 4deg its noticeably cleaner than the sunny mode which hints at a bog 1/4throttle
#3-rain map more effective at the cold extreme of your jetting temp range.

just finished recutting side knobbly,dropped clip to#3,repack muffler in 2deg garage.good to go
Q.anyone made a tool for prising fuel line off carb?ive been using the time honoured method of screwdriver blade into fleshy part of left hand!

2013 ec200r

Last edited by barossi73; 07-13-2015 at 08:59 AM.
Reply With Quote

Old 07-13-2015, 04:28 PM
Leo's Avatar
Leo Leo is offline
Senior Member
Join Date: Sep 2008
Posts: 499

It's good idea cover this hose with exaust tape. Just in case.
Sherco ST300 2015 (Trials)
Reply With Quote

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Similar Threads
Thread Thread Starter Forum Replies Last Post
Switch from 50:1 to 60:1? liv2day Enduro Intake/Carburetion - 2 stroke 31 01-11-2014 05:28 PM
Looking for a key switch.... Novascotiarider Enduro Electrical & Wiring 1 07-06-2013 07:21 AM
map switch shark4465 Enduro Engine - 2 stroke 1 11-18-2012 06:12 PM
map switch, in or out? solstice Enduro Engine - 2 stroke 4 03-16-2012 11:14 AM
Switch Rabbitist General Discussions & Announcements 1 05-24-2011 07:10 PM

All times are GMT -5. The time now is 10:42 AM.

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2023, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org