Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Electrical & Wiring

Enduro Electrical & Wiring Lighting, Ignition, Wiring, Plugs, etc.


Reply
 
Thread Tools Display Modes
  #1  
Old 05-20-2019, 02:46 PM
periclesgsilva periclesgsilva is offline
Member
 
Join Date: Feb 2014
Posts: 65
Default Gasgas EC300 E-Start 2014 Coil Problem

Hello!
I have a 2014 E-start GG Racing 300. Everything running fine until a river cross. After some miles, the bike start to hesitate on low speed. Turning the accelerator, bike run fine. My thought about this: spark plug. After the enduro end, clean the bike, change the spark, same symptom. Checked the reeds (VForce 4), all ok. Checked the battery, charge ok.
After take the gas tank apart, seat, etc., remove the spark plug, turning with my hand the ignition fly wheel, I hear a spark sound coming from the ignition coil. Well, change the ignition coil. Same sound. Click sound, coming from the coil.
Put another coil, same sound. Putting my ear near the cable, the sound come from the cable. Inside the cable, even in the new ignition coil.
My question: the original coil, it's different from the other bikes? I mean, maybe a resistance in this cable? And others simple coils (from another 2 strokes street bike) don't have this resistance and maybe a spark scape inside the cable?
Trying to start the bike (kick or Eletric start) just a explosion and no engine running. Looks like the spark time it's delayed. I think it's because the coil cable.
Running into circles...
Sorry for my confusing English.


Reply With Quote


  #2  
Old 05-20-2019, 04:11 PM
gasgasman's Avatar
gasgasman gasgasman is offline
Super Moderator
 
Join Date: Jul 2006
Location: Pearland Texas
Posts: 4,594
Default

The resistance is the same in the cables. Some bikes have a resistor in the spark plug cap.
The cable screws into the cap and the coil.

I would make sure that the coil is properly grounded.
Reply With Quote
  #3  
Old 05-21-2019, 06:05 AM
periclesgsilva periclesgsilva is offline
Member
 
Join Date: Feb 2014
Posts: 65
Thumbs up

Hello @gasgasman.
Perfectly grounded. I think maybe could be the crankshaft key. I will try to remove the ignition fly wheel and check it.
Thanks for the help!
Reply With Quote
  #4  
Old 05-23-2019, 06:16 AM
periclesgsilva periclesgsilva is offline
Member
 
Join Date: Feb 2014
Posts: 65
Default

GG running! My suspect was right. The flywheel key was broken. Changed and bike running perfect!
Thank you!
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
2014 GasGas EC300 $3500 wilmington_powersports Used Bikes 0 03-31-2017 10:09 AM
Gasgas ec300 Crankcase pressure problem Stijn_M Enduro Engine - 2 stroke 23 09-09-2016 01:36 PM
2014 GasGas EC300 Jetster220 Used Bikes 4 02-12-2016 02:02 PM
gasgas ec300 engine problem jens Enduro Engine - 2 stroke 26 02-08-2012 01:36 PM
Strange Problem With My Gasgas Ec300 Am Ready To Burn It, GasGas.ec300.Andy Enduro Electrical & Wiring 14 01-17-2009 07:59 PM




All times are GMT -5. The time now is 10:21 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org